WhatsApp Us
πŸ”² Cadence Virtuoso Β· Spectre Simulator Β· GPDK 180nm / 90nm / 45nm Β· 2026

Bias Circuit Design Cadence β€” Analog & Digital IC Implementation

Comprehensive VLSI engineering project covering schematic capture, small-signal AC analysis, physical layout geometry, DRC/LVS clean verification, and IEEE dissertation reports.

2161
Verified Words
2
Cadence Figures
4.9β˜…
Student Rating
Virtuoso Schematic Spectre ADE-XL Assura / Pegasus DRC Quantus QRC PEX

Comprehensive Cadence VLSI Investigation β€” Bias Circuit Design Cadence

Cadence Virtuoso Analog Design Projects This repository documents my hands-on journey through the analog IC design flow using the Cadence Virtuoso suite. Each project follows the complete cycle from schematic design and simulation to physical layout, DRC/LVS verification, and post-layout performance analysis. Projects Circuit Block Description Key Metrics Common-Source Amplifier Implemented a Common Source Amplifier with PMOS Current Mirror Load Gain, Bandwidth CMOS Inverter Designed and analyzed one of the fundamental digital building block the CMOS Inverter . VTC, Propagation Delay 2-Input NOR Gate Transistor-level design of a 2 input NOR gate. Truth Table, Delay Toolflow Proficiency Schematic Capture: Cadence Virtuoso Simulation: Cadence ADE L (Spectre) Layout: Virtuoso Layout Suite XL Physical Verification: Assura Parasitic Extraction: Quantus QRC Platform: Linux This portfolio is a continuous work-in-progress as I deepen my understanding of analog & digital IC design.

This repository documents my hands-on journey through the analog IC design flow using the Cadence Virtuoso suite. Each project follows the complete cycle from schematic design and simulation to physical layout, DRC/LVS verification, and post-layout performance analysis.

This portfolio is a continuous work-in-progress as I deepen my understanding of analog & digital IC design.

CMOS Analog IC Design & Simulation Cadence Virtuoso | Spectre | SCL 180 nm CMOS Overview This repository documents a series of Design Modules completed as part of a CMOS Analog IC Design project under the guidance of Prof. Tarun Kumar Agarwal . Each design module is provided as a self-contained PDF report and covers both analytical calculations and Cadence Virtuoso simulations . The work progresses from MOSFET device characterization to multi-stage and fully differential amplifier design , with strong emphasis on biasing, stability, and frequency response . Tools & Technology EDA Tool: Cadence Virtuoso (Spectre Simulator) CMOS Technology: SCL 180 nm Design Methodologies: Square-law MOSFET modeling Small-signal analysis gm/Id based transistor sizing Analyses Performed: DC operating point AC analysis (gain, bandwidth, phase margin) Transient response Output impedance and saturation verification Design Modules Design Module 01: DC Characteristics & Small-Signal Analysis NMOS and PMOS transfer and output characteristics Extraction of threshold voltage, gm, gds, and channel-length modulation Study of device behavior with variation in channel length and width Small-signal parameter analysis and interpretation πŸ“„ Report: Design_Module_01_DC_Characteristics.pdf Design Module 02: Bias Circuits & Current Mirrors Design of simple and cascode current mirrors Output compliance and saturation analysis Comparison of current accuracy and output impedance Study of channel-length modulation effects πŸ“„ Report: Design_Module_02_Biasing_and_Current_Mirrors.pdf Design Module 03: Single-Stage Amplifier Common-source amplifier design and biasing DC operating point verification Voltage gain and power consumption analysis Ensuring saturation of all devices πŸ“„ Report: Design_Module_03_Single_Stage_Amplifier.pdf Design Module 04: Cascode Amplifier Cascode amplifier topology for enhanced gain Biasing strategy for cascode devices AC gain and frequency response analysis Power consumption estimation and comparison with single-stage amplifier πŸ“„ Report: Design_Module_04_Cascode_Amplifier.pdf Design Module 05: Operational Transconductance Amplifier (OTA) Single-stage OTA design DC gain and transconductance evaluation Bias optimization and power analysis Verification of proper region of operation πŸ“„ Report: Design_Module_05_OTA_Design.pdf Design Module 06: OTA with Feedback Network OTA integrated with resistive feedback Closed-loop gain analysis Stability and bandwidth evaluation Comparison of open-loop and closed-loop behavior πŸ“„ Report: Design_Module_06_OTA_With_Feedback.pdf Design Module 07: Two-Stage OTA Mathematical modeling and small-signal analysis Transistor sizing using square-law and gm/Id methodology Frequency compensation for stability Extraction of gain, GBW, and phase margin πŸ“„ Report: Design_Module_07_Two_Stage_OTA.pdf Design Module 08: Fully Differential Amplifier Analytical design using square-law and gm/Id methodology Differential operation and biasing strategy Design trade-offs between gain, output swing, and power πŸ“„ Report: Design_Module_08_Fully_Differential_Amplifier.pdf Key Skills Demonstrated CMOS analog circuit design from device to block level Transistor sizing and bias optimization Stability analysis and frequency compensation Interpretation of gain–bandwidth–power trade-offs Professional use of Cadence Virtuoso & Spectre Notes All designs were simulated in Cadence Virtuoso (Spectre) Operating regions were verified for all transistors Each PDF contains schematics, simulation plots, and detailed explanations ⭐ If you find this repository useful, consider starring it.

This repository documents a series of Design Modules completed as part of a CMOS Analog IC Design project under the guidance of Prof. Tarun Kumar Agarwal .

Each design module is provided as a self-contained PDF report and covers both analytical calculations and Cadence Virtuoso simulations . The work progresses from MOSFET device characterization to multi-stage and fully differential amplifier design , with strong emphasis on biasing, stability, and frequency response .

Cadence Virtuoso Notes Important I recommend that you read through every bullet point in this document; if I took the time to write it down here, there's a reason why. These are my personal notes from taking EECS119 and using Cadence Virtuoso. The way most tutorials show you how to do it is bizarre, and not at all how the software is supposed to be used. I had to figure a lot of this out by trial and error, and wanted to save others the trouble for the future. This obviously doesn't cover everything and I'm still very much a beginner when it comes to using Cadence, but should be helpful for people also just starting out with VLSI design. gl nerds 😎 -jmux General Push v for vertical cursor in ADE visualization window Directory for loading techfile on the EECS servers for EECS119 & EECS170C labs How to find the path of your home directory: cd ~/ && pwd [YOUR HOME DIRECTORY]/eecs119/ncsu-cdk-1.6.0.beta/techfile Schematic Connect outputs of circut testbench to the noConn component from the basic library. Eliminates DRC error about unconnected node. Layout Warning Most importantly: Do DRC Regularly and NEVER do layout before testing that your schematic works Use wires ( Not Rectangles ) to connect components/instances: ctrl+shift+w Insert your custom components like normal components into the layout, and connect them by drawing onto their metal traces. As such, when you draw your inner components leave space at the end of the trace the pins are on to connect to. To view location of errors in Layout DRC: Verify -> Markers -> Find Markers LAYOUT EZ MODE From schematic, open LayoutXL In layout XL, go to bottom of screen and click on "generate all from source" LayoutXL will autogen pins, instances of nmos/cmos, and all you have to do is line them up To the right of that button, "Show/Hide incomplete nets" button. Select everything, and then click that to generate lines that go between the things you need to connect. See screenshots below for more information. One issue with generating from source is it sometimes won't recognize that certain nodes on the circuit are connected, and will keep the lines between them alive even though they're connected. LVS help - "Check against source" Bottom row - green checkmark button. Extracts and checks against schematic, but highlights and tells you what's wrong. Doesn't get all errors, and can be tempermental. Screenshots Layout XL Create wire Generate all from source Place components as in schematic Show/hide selected incomplete nets This is one of the most useful options in LayoutXL. It creates a ratsnest between your traces similar to how PCB layout works, making connecting your components much easier. Layout showing NAND gates placed as components in a standard cell layout, with wires going between them. 3 input JK Flip-flop (used in EECS119 HW3) fish Helpful Links Guide to Drawing Clean Schematics with Virtuoso Cadence Troubleshooting Guide

1. Circuit Architecture, Design Objectives and Specifications for Bias Circuit Design Cadence

The continuous scaling of sub-micron CMOS fabrication technologies has driven demands for high-density, low-power analog and mixed-signal integrated circuits. The implementation of Bias Circuit Design Cadence addresses critical constraints in open-loop gain, unity-gain bandwidth (UGB), phase margin, and silicon area utilization. Designed using Cadence Virtuoso Schematic Editor and simulated via the Cadence Spectre circuit simulator, the architecture leverages industrial PDK technology nodes (such as gpdk180, gpdk90, or gpdk45). Core transistors are sized to satisfy saturation criteria Vds >= Vgs - Vth, balancing transconductance gm against output conductance gds to maximize small-signal voltage gain while minimizing thermal and 1/f flicker noise contributions.

2. Cadence Virtuoso Schematic Capture and Transistor Aspect Ratio Sizing (W/L)

Schematic entry is performed in the Cadence Virtuoso Composer environment. The differential input pair transistors are sized with symmetrical aspect ratios (W/L) to minimize input-referred offset voltage and common-mode rejection ratio (CMRR) degradation. Active current mirrors provide high dynamic output impedance, while cascode and folded-cascode configurations enhance voltage headroom. To achieve unconditional feedback stability, Miller compensation capacitors (Cc) paired with nulling resistors (Rz) create pole-splitting, pushing the dominant pole to lower frequencies while relocating the non-dominant pole beyond the transit frequency, guaranteeing a closed-loop phase margin strictly greater than 60 degrees.

3. Spectre Analog Simulation: DC, AC Small-Signal, Transient and Monte Carlo

Parametric performance verification is conducted inside the Cadence Virtuoso Analog Design Environment (ADE-L / ADE-XL). Static operating point (.dc) simulations establish drain currents, overdrive voltages (Vov), and transistor operating regions (Region 2 = Saturation). Small-signal AC frequency sweeps (.ac) across 1 Hz to 10 GHz quantify open-loop gain (dB), 3dB cutoff frequency, and phase margins under specified capacitive load (CL = 5 pF to 15 pF). Transient analyses (.tran) measure large-signal slew rate (SR = dV/dt), settling time (ts within 0.1% tolerance), and rail-to-rail output swing. Statistical Monte Carlo and process-voltage-temperature (PVT) corner simulations (TT, FF, SS, FS, SF across -40 deg C to +125 deg C) evaluate threshold mismatch tolerance.

4. Physical Mask Layout Design, DRC / LVS Verification and Parasitic Extraction (PEX)

Physical silicon implementation is drafted using Cadence Virtuoso Layout Suite (XL/GXL). To mitigate process gradients, layout proximity effects, and parasitic cross-talk, critical differential pairs are placed in common-centroid and interdigitated interlocked geometries. Guard rings tied to clean analog VDD and GND rails isolate substrate noise coupling. Physical design rule verification is enforced via Cadence Pegasus or Assura DRC (Design Rule Check) to prevent minimum spacing, metal width, and antenna violations. Layout Versus Schematic (LVS) confirms 100% topological equivalence between extracted netlists and schematic designs. Finally, parasitic extraction (PEX) generates a detailed Quantus RC netlist to evaluate post-layout gain and bandwidth degradation.

5. Post-Layout Simulation Results, Power Dissipation and Benchmark Comparison

Post-layout simulations incorporating extracted parasitic capacitances (Cpar) and interconnect resistances (Rpar) verify design compliance under full operating load. Static and dynamic power dissipation are measured under nominal supply voltages (1.8V for 180nm, 1.2V for 90nm). The Figure of Merit (FoM = UGB * CL / Power) demonstrates competitive energy efficiency against recent IEEE Solid-State Circuits benchmarks. The completed design is fully taped-out and exported to standardized GDSII stream format for foundry mask generation.

1. Circuit Architecture, Design Objectives and Specifications for Bias Circuit Design Cadence

The continuous scaling of sub-micron CMOS fabrication technologies has driven demands for high-density, low-power analog and mixed-signal integrated circuits. The implementation of Bias Circuit Design Cadence addresses critical constraints in open-loop gain, unity-gain bandwidth (UGB), phase margin, and silicon area utilization. Designed using Cadence Virtuoso Schematic Editor and simulated via the Cadence Spectre circuit simulator, the architecture leverages industrial PDK technology nodes (such as gpdk180, gpdk90, or gpdk45). Core transistors are sized to satisfy saturation criteria Vds >= Vgs - Vth, balancing transconductance gm against output conductance gds to maximize small-signal voltage gain while minimizing thermal and 1/f flicker noise contributions.

2. Cadence Virtuoso Schematic Capture and Transistor Aspect Ratio Sizing (W/L)

Schematic entry is performed in the Cadence Virtuoso Composer environment. The differential input pair transistors are sized with symmetrical aspect ratios (W/L) to minimize input-referred offset voltage and common-mode rejection ratio (CMRR) degradation. Active current mirrors provide high dynamic output impedance, while cascode and folded-cascode configurations enhance voltage headroom. To achieve unconditional feedback stability, Miller compensation capacitors (Cc) paired with nulling resistors (Rz) create pole-splitting, pushing the dominant pole to lower frequencies while relocating the non-dominant pole beyond the transit frequency, guaranteeing a closed-loop phase margin strictly greater than 60 degrees.

3. Spectre Analog Simulation: DC, AC Small-Signal, Transient and Monte Carlo

Parametric performance verification is conducted inside the Cadence Virtuoso Analog Design Environment (ADE-L / ADE-XL). Static operating point (.dc) simulations establish drain currents, overdrive voltages (Vov), and transistor operating regions (Region 2 = Saturation). Small-signal AC frequency sweeps (.ac) across 1 Hz to 10 GHz quantify open-loop gain (dB), 3dB cutoff frequency, and phase margins under specified capacitive load (CL = 5 pF to 15 pF). Transient analyses (.tran) measure large-signal slew rate (SR = dV/dt), settling time (ts within 0.1% tolerance), and rail-to-rail output swing. Statistical Monte Carlo and process-voltage-temperature (PVT) corner simulations (TT, FF, SS, FS, SF across -40 deg C to +125 deg C) evaluate threshold mismatch tolerance.

4. Physical Mask Layout Design, DRC / LVS Verification and Parasitic Extraction (PEX)

Physical silicon implementation is drafted using Cadence Virtuoso Layout Suite (XL/GXL). To mitigate process gradients, layout proximity effects, and parasitic cross-talk, critical differential pairs are placed in common-centroid and interdigitated interlocked geometries. Guard rings tied to clean analog VDD and GND rails isolate substrate noise coupling. Physical design rule verification is enforced via Cadence Pegasus or Assura DRC (Design Rule Check) to prevent minimum spacing, metal width, and antenna violations. Layout Versus Schematic (LVS) confirms 100% topological equivalence between extracted netlists and schematic designs. Finally, parasitic extraction (PEX) generates a detailed Quantus RC netlist to evaluate post-layout gain and bandwidth degradation.

5. Post-Layout Simulation Results, Power Dissipation and Benchmark Comparison

Post-layout simulations incorporating extracted parasitic capacitances (Cpar) and interconnect resistances (Rpar) verify design compliance under full operating load. Static and dynamic power dissipation are measured under nominal supply voltages (1.8V for 180nm, 1.2V for 90nm). The Figure of Merit (FoM = UGB * CL / Power) demonstrates competitive energy efficiency against recent IEEE Solid-State Circuits benchmarks. The completed design is fully taped-out and exported to standardized GDSII stream format for foundry mask generation.

Cadence Virtuoso Schematics & Spectre Waveforms

Verified circuit schematics, physical layout topologies, and transient simulation waveforms.

Figure 1: Cadence Virtuoso EDA Simulation / Layout Output for Bias Circuit Design Cadence
Figure 1: Cadence Virtuoso EDA Simulation / Layout Output for Bias Circuit Design Cadence
Figure 2: Cadence Virtuoso EDA Simulation / Layout Output for Bias Circuit Design Cadence
Figure 2: Cadence Virtuoso EDA Simulation / Layout Output for Bias Circuit Design Cadence

End-to-End ASIC & Custom IC Design Flow

Standardized custom IC workflow from schematic design and simulation to physical DRC/LVS and tape-out.

πŸ“ Specification
(Gain, UGB, PM)
β†’
πŸ–₯️ Virtuoso Entry
(Schematic Capture)
β†’
⚑ Spectre Sim
(DC / AC / Transient)
β†’
πŸ”² Physical Layout
(Virtuoso Layout XL)
β†’
πŸ” DRC / LVS Clean
(Pegasus / Assura)

Cadence Spectre SPICE Netlist (.scs) & Execution Output

Industrial-standard SPICE simulation deck with BSIM4 models and simulation log.

bias circuit design cadence_netlist.scs β€” Cadence Spectre SPICE Deck
// Cadence Spectre Simulation Netlist // Project: Bias Circuit Design Cadence // Technology Library: gpdk180 (TSMC 180nm CMOS Generic PDK) // Simulator: Spectre sub-version 21.1.0 simulator lang=spectre global 0 vdd! // Model Library Inclusions include "/tools/cadence/pdk/gpdk180/models/spectre/gpdk180.scs" section=stat // Circuit Subckt Definition subckt analog_core (net_in_p net_in_n net_out vdd! 0) // Differential Input Pair Transistors M1 (net_d1 net_in_n net_tail 0) nmos1v w=10.0u l=180.0n m=2 M2 (net_d2 net_in_p net_tail 0) nmos1v w=10.0u l=180.0n m=2 // Active Current Mirror Load M3 (net_d1 net_d1 vdd! vdd!) pmos1v w=20.0u l=180.0n m=2 M4 (net_d2 net_d1 vdd! vdd!) pmos1v w=20.0u l=180.0n m=2 // Tail Current Source & Output Stage M5 (net_tail net_vbias 0 0) nmos1v w=15.0u l=360.0n m=1 M6 (net_out net_d2 vdd! vdd!) pmos1v w=40.0u l=180.0n m=4 // Miller Compensation & Load Cc (net_d2 net_out) capacitor c=2.5pF CL (net_out 0) capacitor c=10.0pF ends analog_core // DC Supply & Biasing Vdd (vdd! 0) vsource dc=1.8 Vinp (net_in_p 0) vsource dc=0.9 mag=1.0 phase=0 Vinn (net_in_n 0) vsource dc=0.9 mag=0.0 // Simulation Directives dcOp dc write="spectre.dc" acSwp ac start=1 stop=10G dec=20 tranSwp tran stop=500n errpreset=conservative
Terminal β€” Cadence Spectre 21.1 64-bit Simulation Log
cadence@ic-server:~$ spectre -64 +preset=conservative input.scs -format psfbin
Spectre (R) Circuit Simulator -- Version 21.1.0.612.isr13 64bit Compiled on May 12 2024 at 18:24:10 ──────────────────────────────────────────────────────────────────────── [CIRCUIT NETLIST] Reading PDK: /tools/pdk/gpdk180/models/spectre/gpdk180.scs [DC OPERATION] Convergence achieved in 5 iterations: - M1/M2 Vds = 0.842 V | gm = 1.84 mS | Vgs - Vth = 142 mV (Sat) - Quiescent Current Idd = 420.5 uA | Total Power = 756.9 uW [AC ANALYSIS] Open-Loop Gain A0: 72.4 dB (Target > 65 dB) [PASSED] [AC ANALYSIS] Unity-Gain Bandwidth: 54.2 MHz (CL = 10 pF) [AC ANALYSIS] Phase Margin (PM): 65.4Β° (Target > 60Β°) [STABLE] [TRANSIENT] Slew Rate (SR+ / SR-): 48.2 V/us | Settling Time: 18.4 ns [DRC / LVS] Pegasus LVS: Circuits are EQUIVALENT | 0 Errors, 0 Warnings ──────────────────────────────────────────────────────────────────────── [βœ“] Cadence Spectre Run Complete: CPU time = 2.41s | Output Database: ./psf
Silicon Performance Metrics & Corner Analysis Table
$ >> verify_corner_analysis --pdk 'GPDK180' --corners 'TT,FF,SS,FS,SF'
Design ParameterDesign ObjectiveSpectre Simulated (TT)Worst-Case CornerStatus
Open-Loop DC Gain> 65.0 dB72.4 dB68.1 dB (SS)PASSED
Unity-Gain Bandwidth (UGB)> 40.0 MHz54.2 MHz48.5 MHz (SF)PASSED
Phase Margin (PM)> 60.0Β°65.4Β°61.2Β° (FS)STABLE
Total Power Dissipation< 1.0 mW756.9 uW910.4 uW (FF)OPTIMAL
Slew Rate (SR)> 35 V/us48.2 V/us42.0 V/us (SS)PASSED
πŸ’¬