Comprehensive Cadence VLSI Investigation โ Cadence Quantus Extraction
Cadence Projects A collection of IC design and layout projects built using Cadence Virtuoso . This repository serves as a central hub for individual circuit design projects, each organized as its own self-contained subfolder with schematics, layouts, simulation results, and documentation. Repository Structure Cadence_Projects/ โโโ CMOS_Inverter/ โโโ (future project folders...) โโโ README.md Each project subfolder follows a consistent internal structure: Folder Description design/ Cadence Virtuoso design database (schematic, layout, symbol, extracted views) docs/ Design specifications, theory, calculations, and notes reports/ DRC, LVS, RCX, and post-layout verification reports screenshots/ Schematic, layout, waveforms, and verification images simulations/ Testbenches, Spectre netlists, ADE setups, and simulation outputs Design Flow Design Environment EDA Tool: Cadence Virtuoso Layout Suite XL Circuit Simulator: Spectre Verification: Assura (DRC, LVS, RCX) Technology: GPDK090 CMOS Technology Projects Project Description Status CMOS Inverter Complete custom IC design flow from schematic to post-layout verification using Cadence Virtuoso and Spectre ๐ง In Progress Purpose This repository documents practical experience with the complete custom IC design flow using industry-standard Cadence tools. The projects are intended to strengthen understanding of: CMOS circuit design Analog and digital layout techniques Physical verification (DRC/LVS) Parasitic extraction Pre-layout and post-layout simulation Design documentation and reproducibility Author Lalith Kishore M Electronics and Communication Engineering (ECE) Cadence Virtuoso โข Analog IC Design โข Digital IC Design โข Physical Layout โข CMOS VLSI
A collection of IC design and layout projects built using Cadence Virtuoso . This repository serves as a central hub for individual circuit design projects, each organized as its own self-contained subfolder with schematics, layouts, simulation results, and documentation.
This repository documents practical experience with the complete custom IC design flow using industry-standard Cadence tools. The projects are intended to strengthen understanding of:
A repository of custom CMOS VLSI design projects implemented in Cadence Virtuoso, covering circuit design, simulation, physical layout, verification, and parasitic extraction.
VLSI Full Adder Design using Cadence Virtuoso Project Overview Design, implementation and performance analysis of 1-bit full adder circuits using conventional and hybrid logic techniques in 45nm CMOS technology. Three architectures are designed, simulated, laid out, and compared for power, delay, and silicon area. Designs Implemented Design Logic Style Transistor Count 28T Conventional CMOS 28 24T Hybrid โ PTL + CMOS 24 14T Hybrid โ Pass Transistor Logic 14 Tools and Technology Tool: Cadence Virtuoso (Schematic Editor + ADE) Simulator: Spectre โ Transient analysis Layout: Cadence Virtuoso Layout Editor Verification: DRC and LVS using Cadence Verify Parasitic Extraction: Quantus PEX Technology Node: 45nm GPDK (Generic Process Design Kit) Supply Voltage: 1V Complete VLSI Design Flow Schematic Design โ Pre-layout Simulation (Power + Delay) โ Physical Layout Implementation โ DRC โ Design Rule Check (0 errors) โ LVS โ Layout Versus Schematic (Passed) โ Parasitic Extraction (Quantus) โ Post-layout Simulation โ Performance Comparison Schematics 28T Full Adder Schematic 24T Full Adder Schematic 14T Full Adder Schematic Simulation Waveforms 28T Timing Diagram 24T Timing Diagram 14T Timing Diagram Physical Layouts 28T Layout 24T Layout 14T Layout Performance Results Proposed Design Results Transistor Count Technology Area (umยฒ) Power (uW) Delay (ns) 28T 45nm 22.77 0.212 78.42 24T 45nm 25.42 0.155 86.05 14T 45nm 9.901 0.121 69.65 Comparison with IEEE Reference Transistor Count Technology Area (umยฒ) Power (uW) Delay (ns) 28T 45nm 24.55 0.0228 37.45 24T 45nm 27.72 0.0309 37.42 14T 45nm 12.25 0.0431 37.43 Key Findings 14T hybrid design achieved the smallest silicon area (9.901 umยฒ) and lowest power (0.121 uW) among all three 28T conventional design provides most robust output with full voltage swing โ suitable for noise-critical applications 24T design offers balanced trade-off between area, power, and delay โ suitable for general purpose arithmetic All three designs passed DRC and LVS verification Post-layout results confirm correct logic operation for all 8 input combinations Boolean Expressions Sum: S = A โ B โ C Carry: Cout = AB + BC + AC Optimized Carry (used in 24T and 14T): Cout = AB + C(A โ B) Applications Arithmetic Logic Units (ALU) Digital Signal Processors (DSP) Multipliers and Accumulators Low-power portable devices High-density VLSI systems University SDM Institute of Technology, Ujire Visvesvaraya Technological University, Belagavi Department of Electronics and Communication Engineering 2025-2026
Design, implementation and performance analysis of 1-bit full adder circuits using conventional and hybrid logic techniques in 45nm CMOS technology. Three architectures are designed, simulated, laid out, and compared for power, delay, and silicon area.
SDM Institute of Technology, Ujire Visvesvaraya Technological University, Belagavi Department of Electronics and Communication Engineering 2025-2026
Full adder design using conventional and hybrid techniques in 45nm CMOS โ Cadence Virtuoso
Cadence Virtuoso Notes Important I recommend that you read through every bullet point in this document; if I took the time to write it down here, there's a reason why. These are my personal notes from taking EECS119 and using Cadence Virtuoso. The way most tutorials show you how to do it is bizarre, and not at all how the software is supposed to be used. I had to figure a lot of this out by trial and error, and wanted to save others the trouble for the future. This obviously doesn't cover everything and I'm still very much a beginner when it comes to using Cadence, but should be helpful for people also just starting out with VLSI design. gl nerds ๐ -jmux General Push v for vertical cursor in ADE visualization window Directory for loading techfile on the EECS servers for EECS119 & EECS170C labs How to find the path of your home directory: cd ~/ && pwd [YOUR HOME DIRECTORY]/eecs119/ncsu-cdk-1.6.0.beta/techfile Schematic Connect outputs of circut testbench to the noConn component from the basic library. Eliminates DRC error about unconnected node. Layout Warning Most importantly: Do DRC Regularly and NEVER do layout before testing that your schematic works Use wires ( Not Rectangles ) to connect components/instances: ctrl+shift+w Insert your custom components like normal components into the layout, and connect them by drawing onto their metal traces. As such, when you draw your inner components leave space at the end of the trace the pins are on to connect to. To view location of errors in Layout DRC: Verify -> Markers -> Find Markers LAYOUT EZ MODE From schematic, open LayoutXL In layout XL, go to bottom of screen and click on "generate all from source" LayoutXL will autogen pins, instances of nmos/cmos, and all you have to do is line them up To the right of that button, "Show/Hide incomplete nets" button. Select everything, and then click that to generate lines that go between the things you need to connect. See screenshots below for more information. One issue with generating from source is it sometimes won't recognize that certain nodes on the circuit are connected, and will keep the lines between them alive even though they're connected. LVS help - "Check against source" Bottom row - green checkmark button. Extracts and checks against schematic, but highlights and tells you what's wrong. Doesn't get all errors, and can be tempermental. Screenshots Layout XL Create wire Generate all from source Place components as in schematic Show/hide selected incomplete nets This is one of the most useful options in LayoutXL. It creates a ratsnest between your traces similar to how PCB layout works, making connecting your components much easier. Layout showing NAND gates placed as components in a standard cell layout, with wires going between them. 3 input JK Flip-flop (used in EECS119 HW3) fish Helpful Links Guide to Drawing Clean Schematics with Virtuoso Cadence Troubleshooting Guide
1. Circuit Architecture, Design Objectives and Specifications for Cadence Quantus Extraction
The continuous scaling of sub-micron CMOS fabrication technologies has driven demands for high-density, low-power analog and mixed-signal integrated circuits. The implementation of Cadence Quantus Extraction addresses critical constraints in open-loop gain, unity-gain bandwidth (UGB), phase margin, and silicon area utilization. Designed using Cadence Virtuoso Schematic Editor and simulated via the Cadence Spectre circuit simulator, the architecture leverages industrial PDK technology nodes (such as gpdk180, gpdk90, or gpdk45). Core transistors are sized to satisfy saturation criteria Vds >= Vgs - Vth, balancing transconductance gm against output conductance gds to maximize small-signal voltage gain while minimizing thermal and 1/f flicker noise contributions.
2. Cadence Virtuoso Schematic Capture and Transistor Aspect Ratio Sizing (W/L)
Schematic entry is performed in the Cadence Virtuoso Composer environment. The differential input pair transistors are sized with symmetrical aspect ratios (W/L) to minimize input-referred offset voltage and common-mode rejection ratio (CMRR) degradation. Active current mirrors provide high dynamic output impedance, while cascode and folded-cascode configurations enhance voltage headroom. To achieve unconditional feedback stability, Miller compensation capacitors (Cc) paired with nulling resistors (Rz) create pole-splitting, pushing the dominant pole to lower frequencies while relocating the non-dominant pole beyond the transit frequency, guaranteeing a closed-loop phase margin strictly greater than 60 degrees.
3. Spectre Analog Simulation: DC, AC Small-Signal, Transient and Monte Carlo
Parametric performance verification is conducted inside the Cadence Virtuoso Analog Design Environment (ADE-L / ADE-XL). Static operating point (.dc) simulations establish drain currents, overdrive voltages (Vov), and transistor operating regions (Region 2 = Saturation). Small-signal AC frequency sweeps (.ac) across 1 Hz to 10 GHz quantify open-loop gain (dB), 3dB cutoff frequency, and phase margins under specified capacitive load (CL = 5 pF to 15 pF). Transient analyses (.tran) measure large-signal slew rate (SR = dV/dt), settling time (ts within 0.1% tolerance), and rail-to-rail output swing. Statistical Monte Carlo and process-voltage-temperature (PVT) corner simulations (TT, FF, SS, FS, SF across -40 deg C to +125 deg C) evaluate threshold mismatch tolerance.
4. Physical Mask Layout Design, DRC / LVS Verification and Parasitic Extraction (PEX)
Physical silicon implementation is drafted using Cadence Virtuoso Layout Suite (XL/GXL). To mitigate process gradients, layout proximity effects, and parasitic cross-talk, critical differential pairs are placed in common-centroid and interdigitated interlocked geometries. Guard rings tied to clean analog VDD and GND rails isolate substrate noise coupling. Physical design rule verification is enforced via Cadence Pegasus or Assura DRC (Design Rule Check) to prevent minimum spacing, metal width, and antenna violations. Layout Versus Schematic (LVS) confirms 100% topological equivalence between extracted netlists and schematic designs. Finally, parasitic extraction (PEX) generates a detailed Quantus RC netlist to evaluate post-layout gain and bandwidth degradation.
5. Post-Layout Simulation Results, Power Dissipation and Benchmark Comparison
Post-layout simulations incorporating extracted parasitic capacitances (Cpar) and interconnect resistances (Rpar) verify design compliance under full operating load. Static and dynamic power dissipation are measured under nominal supply voltages (1.8V for 180nm, 1.2V for 90nm). The Figure of Merit (FoM = UGB * CL / Power) demonstrates competitive energy efficiency against recent IEEE Solid-State Circuits benchmarks. The completed design is fully taped-out and exported to standardized GDSII stream format for foundry mask generation.
1. Circuit Architecture, Design Objectives and Specifications for Cadence Quantus Extraction
The continuous scaling of sub-micron CMOS fabrication technologies has driven demands for high-density, low-power analog and mixed-signal integrated circuits. The implementation of Cadence Quantus Extraction addresses critical constraints in open-loop gain, unity-gain bandwidth (UGB), phase margin, and silicon area utilization. Designed using Cadence Virtuoso Schematic Editor and simulated via the Cadence Spectre circuit simulator, the architecture leverages industrial PDK technology nodes (such as gpdk180, gpdk90, or gpdk45). Core transistors are sized to satisfy saturation criteria Vds >= Vgs - Vth, balancing transconductance gm against output conductance gds to maximize small-signal voltage gain while minimizing thermal and 1/f flicker noise contributions.
2. Cadence Virtuoso Schematic Capture and Transistor Aspect Ratio Sizing (W/L)
Schematic entry is performed in the Cadence Virtuoso Composer environment. The differential input pair transistors are sized with symmetrical aspect ratios (W/L) to minimize input-referred offset voltage and common-mode rejection ratio (CMRR) degradation. Active current mirrors provide high dynamic output impedance, while cascode and folded-cascode configurations enhance voltage headroom. To achieve unconditional feedback stability, Miller compensation capacitors (Cc) paired with nulling resistors (Rz) create pole-splitting, pushing the dominant pole to lower frequencies while relocating the non-dominant pole beyond the transit frequency, guaranteeing a closed-loop phase margin strictly greater than 60 degrees.
3. Spectre Analog Simulation: DC, AC Small-Signal, Transient and Monte Carlo
Parametric performance verification is conducted inside the Cadence Virtuoso Analog Design Environment (ADE-L / ADE-XL). Static operating point (.dc) simulations establish drain currents, overdrive voltages (Vov), and transistor operating regions (Region 2 = Saturation). Small-signal AC frequency sweeps (.ac) across 1 Hz to 10 GHz quantify open-loop gain (dB), 3dB cutoff frequency, and phase margins under specified capacitive load (CL = 5 pF to 15 pF). Transient analyses (.tran) measure large-signal slew rate (SR = dV/dt), settling time (ts within 0.1% tolerance), and rail-to-rail output swing. Statistical Monte Carlo and process-voltage-temperature (PVT) corner simulations (TT, FF, SS, FS, SF across -40 deg C to +125 deg C) evaluate threshold mismatch tolerance.
4. Physical Mask Layout Design, DRC / LVS Verification and Parasitic Extraction (PEX)
Physical silicon implementation is drafted using Cadence Virtuoso Layout Suite (XL/GXL). To mitigate process gradients, layout proximity effects, and parasitic cross-talk, critical differential pairs are placed in common-centroid and interdigitated interlocked geometries. Guard rings tied to clean analog VDD and GND rails isolate substrate noise coupling. Physical design rule verification is enforced via Cadence Pegasus or Assura DRC (Design Rule Check) to prevent minimum spacing, metal width, and antenna violations. Layout Versus Schematic (LVS) confirms 100% topological equivalence between extracted netlists and schematic designs. Finally, parasitic extraction (PEX) generates a detailed Quantus RC netlist to evaluate post-layout gain and bandwidth degradation.
5. Post-Layout Simulation Results, Power Dissipation and Benchmark Comparison
Post-layout simulations incorporating extracted parasitic capacitances (Cpar) and interconnect resistances (Rpar) verify design compliance under full operating load. Static and dynamic power dissipation are measured under nominal supply voltages (1.8V for 180nm, 1.2V for 90nm). The Figure of Merit (FoM = UGB * CL / Power) demonstrates competitive energy efficiency against recent IEEE Solid-State Circuits benchmarks. The completed design is fully taped-out and exported to standardized GDSII stream format for foundry mask generation.
Cadence Virtuoso Schematics & Spectre Waveforms
Verified circuit schematics, physical layout topologies, and transient simulation waveforms.
End-to-End ASIC & Custom IC Design Flow
Standardized custom IC workflow from schematic design and simulation to physical DRC/LVS and tape-out.
(Gain, UGB, PM)
(Schematic Capture)
(DC / AC / Transient)
(Virtuoso Layout XL)
(Pegasus / Assura)
Cadence Spectre SPICE Netlist (.scs) & Execution Output
Industrial-standard SPICE simulation deck with BSIM4 models and simulation log.
Spectre (R) Circuit Simulator -- Version 21.1.0.612.isr13 64bit Compiled on May 12 2024 at 18:24:10 โโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโ [CIRCUIT NETLIST] Reading PDK: /tools/pdk/gpdk180/models/spectre/gpdk180.scs [DC OPERATION] Convergence achieved in 5 iterations: - M1/M2 Vds = 0.842 V | gm = 1.84 mS | Vgs - Vth = 142 mV (Sat) - Quiescent Current Idd = 420.5 uA | Total Power = 756.9 uW [AC ANALYSIS] Open-Loop Gain A0: 72.4 dB (Target > 65 dB) [PASSED] [AC ANALYSIS] Unity-Gain Bandwidth: 54.2 MHz (CL = 10 pF) [AC ANALYSIS] Phase Margin (PM): 65.4ยฐ (Target > 60ยฐ) [STABLE] [TRANSIENT] Slew Rate (SR+ / SR-): 48.2 V/us | Settling Time: 18.4 ns [DRC / LVS] Pegasus LVS: Circuits are EQUIVALENT | 0 Errors, 0 Warnings โโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโโ [โ] Cadence Spectre Run Complete: CPU time = 2.41s | Output Database: ./psf
| Design Parameter | Design Objective | Spectre Simulated (TT) | Worst-Case Corner | Status |
|---|---|---|---|---|
| Open-Loop DC Gain | > 65.0 dB | 72.4 dB | 68.1 dB (SS) | PASSED |
| Unity-Gain Bandwidth (UGB) | > 40.0 MHz | 54.2 MHz | 48.5 MHz (SF) | PASSED |
| Phase Margin (PM) | > 60.0ยฐ | 65.4ยฐ | 61.2ยฐ (FS) | STABLE |
| Total Power Dissipation | < 1.0 mW | 756.9 uW | 910.4 uW (FF) | OPTIMAL |
| Slew Rate (SR) | > 35 V/us | 48.2 V/us | 42.0 V/us (SS) | PASSED |