WhatsApp Us
๐Ÿ”ฒ Cadence Virtuoso ยท Spectre Simulator ยท GPDK 180nm / 90nm / 45nm ยท 2026

Charge Pump PLL Cadence โ€” Analog & Digital IC Implementation

Comprehensive VLSI engineering project covering schematic capture, small-signal AC analysis, physical layout geometry, DRC/LVS clean verification, and IEEE dissertation reports.

2224
Verified Words
2
Cadence Figures
4.9โ˜…
Student Rating
Virtuoso Schematic Spectre ADE-XL Assura / Pegasus DRC Quantus QRC PEX

Comprehensive Cadence VLSI Investigation โ€” Charge Pump PLL Cadence

Design and Simulation of a Phase-Locked Loop (PLL) in Cadence Virtuoso Overview This repository contains the transistor-level schematic designs and transient simulation results for a Phase-Locked Loop (PLL) architecture, implemented in Cadence Virtuoso. The design integrates a Phase Frequency Detector (PFD), Charge Pump (CP), Loop Filter, Voltage-Controlled Oscillator (VCO), and a multi-stage Frequency Divider feedback loop. Sub-Block Design & Schematic Specifications 1. Phase Frequency Detector (PFD) Function: Detects phase and frequency discrepancies between the reference input ( $V_{IN}$ ) and the feedback divider signal. Architecture: Built using two D-Flip-Flops with 2-input NOR gates ( NOR2 ) and a reset path utilizing a 2-input NAND gate ( nand2 ) and an Inverter ( INV ). Outputs: UP and DN pulse control signals driving the Charge Pump. 2. Charge Pump (CP) Function: Translates digital UP and DN error signals into continuous current pulses to charge or discharge the passive loop filter. Implementation: Complementary PMOS ( pmos2v ) and NMOS ( nmos2v ) arrays controlled via inverter logic. 3. Voltage-Controlled Oscillator (VCO) Function: Generates the high-frequency clock signal proportional to the incoming control voltage ( $V_{ctrl}$ ). Implementation: CMOS Ring Oscillator architecture employing scaled PMOS/NMOS pairs. 4. Frequency Divider Network Feedback division is accomplished via a cascaded divider hierarchy: TSPC Divide-by-2 Stage: Designed using True Single-Phase Clocked (TSPC) D-Flip-Flops operating at $V_{DD} = 1.8\text{ V}$ . Divide-by-3 Stage: Implemented using D-Flip-Flops paired with 2-input NAND gates. Divide-by-5 Stage: Sequential logic implementation using D-Flip-Flops. Top-Level Divider Loop: Configured through modular stages ( /2 , /3 , /5 ) to establish feedback locking. 5. Loop Filter Topology: Passive second-order RC network. Component Values: Series Resistor ( $R_1$ ): $18\text{ k}\Omega$ Series Capacitor ( $C_1$ ): $207.2\text{ fF}$ Parallel Ripple-Suppression Capacitor ( $C_2$ ): $16\text{ fF}$ Simulation Results Transient analysis was conducted over a $5\text{ }\mu\text{s}$ duration using Cadence Spectre under a $1.8\text{ V}$ power supply. Parameter / Signal Value / Observation Supply Voltage ( $V_{DD}$ ) $1.8\text{ V}$ VCO Output Frequency $1.20418\text{ GHz}$ ( 1.20418G ) Control Voltage ( $V_{ctrl}$ ) Stabilizes at $\sim 0.9\text{ V}$ after locking Lock Time $< 1.0\text{ }\mu\text{s}$ Key Observations VCO Waveform: High-frequency stable clock output oscillating at $1.204\text{ GHz}$ . Control Line ( $V_{ctrl}$ ): Settles smoothly to $\sim 0.9\text{ V}$ with minimal voltage ripple post-lock. PFD Signals ( UP / DN ): Dynamic pulse-width modulation adjusting loop synchronization until phase lock is achieved. Tools & Requirements EDA Suite: Cadence Virtuoso IC Design Platform Simulator: Cadence Spectre Simulation Platform Technology: Standard CMOS Technology Node ( $1.8\text{ V}$ Supply)

This repository contains the transistor-level schematic designs and transient simulation results for a Phase-Locked Loop (PLL) architecture, implemented in Cadence Virtuoso.

The design integrates a Phase Frequency Detector (PFD), Charge Pump (CP), Loop Filter, Voltage-Controlled Oscillator (VCO), and a multi-stage Frequency Divider feedback loop.

Transient analysis was conducted over a $5\text{ }\mu\text{s}$ duration using Cadence Spectre under a $1.8\text{ V}$ power supply.

Charge Pump PLL Design using Cadence Virtuoso A complete transistor-level Charge Pump Phase-Locked Loop (CP-PLL) designed and verified in Cadence Virtuoso using GPDK090 (90 nm CMOS Technology) . ๐Ÿ“Œ Project Overview The objective of this project was to design and integrate all building blocks of a Charge Pump PLL at the transistor level and verify stable phase and frequency locking through simulation. ๐Ÿงฉ Building Blocks Phase Frequency Detector (PFD) Charge Pump Second-Order Passive Loop Filter 5-Stage Current-Starved Ring VCO Divide-by-8 Frequency Divider Complete PLL Integration (closed-loop) ๐Ÿ” PLL Architecture Reference Clock โ†’ PFD โ†’ Charge Pump โ†’ Loop Filter โ†’ 5-Stage Current-Starved Ring VCO โ”‚ โ–ผ Divide-by-8 Divider (Feedback) โš™๏ธ Project Specifications Parameter Value Technology GPDK090 (90 nm) Supply Voltage (VDD) 1.2 V Architecture Charge Pump PLL Reference Frequency (Fref) 301.25 MHz Nominal Output Frequency 2.41 GHz VCO Tuning Range 2.332 GHz โ€“ 2.504 GHz Average Kvco 172 MHz/V Peak Kvco โ‰ˆ 330 MHz/V ๐Ÿงฑ Design Blocks Block Function PFD Compares the reference and feedback clock edges and generates UP/DOWN control pulses Charge Pump Converts UP/DOWN pulses into a proportional charge/discharge current Loop Filter Integrates the charge pump current into a stable VCO control voltage VCO 5-stage current-starved ring oscillator, tuned by the control voltage Divider Divide-by-8 feedback path that closes the loop ๐Ÿงฎ Mathematical Model Phase error: ฯ†e = ฯ†ref โˆ’ ฯ†fb Feedback and output frequency relation: Ffb = Fvco / N Fvco = N ร— Fref VCO gain: Kvco = ฮ”f / ฮ”Vc โ‰ˆ 172 MHz/V Average charge pump current: Iavg = Icp ร— (tUP โˆ’ tDOWN) / Tref At lock: Iavg โ‰ˆ 0 ยตA ๐Ÿ“Š Simulation Results โœ… Successful PLL lock achieved โœ… Stable phase and frequency synchronization โœ… VCO characterization completed โœ… Kvco extraction performed โœ… Divider functionality verified ๐Ÿ› ๏ธ Software & Tools Used Cadence Virtuoso Spectre Simulator GPDK090 PDK ๐ŸŽฏ Skills Demonstrated Analog CMOS Design PLL Design & Closed-Loop Verification Charge Pump Design Ring Oscillator Design Cadence Virtuoso Schematic Entry & Simulation Spectre-based Simulation and Debugging ๐Ÿ“ˆ Results Summary The complete transistor-level Charge Pump PLL achieved stable phase and frequency locking, with a nominal output frequency of approximately 2.41 GHz . ๐Ÿ‘ค Author Anant B.Tech โ€“ VLSI Engineering National Institute of Technology, Kurukshetra ๐Ÿ“ Note This repository contains documentation, schematics, and waveforms only. Proprietary PDK files are not included .

1. Circuit Architecture, Design Objectives and Specifications for Charge Pump PLL Cadence

The continuous scaling of sub-micron CMOS fabrication technologies has driven demands for high-density, low-power analog and mixed-signal integrated circuits. The implementation of Charge Pump PLL Cadence addresses critical constraints in open-loop gain, unity-gain bandwidth (UGB), phase margin, and silicon area utilization. Designed using Cadence Virtuoso Schematic Editor and simulated via the Cadence Spectre circuit simulator, the architecture leverages industrial PDK technology nodes (such as gpdk180, gpdk90, or gpdk45). Core transistors are sized to satisfy saturation criteria Vds >= Vgs - Vth, balancing transconductance gm against output conductance gds to maximize small-signal voltage gain while minimizing thermal and 1/f flicker noise contributions.

2. Cadence Virtuoso Schematic Capture and Transistor Aspect Ratio Sizing (W/L)

Schematic entry is performed in the Cadence Virtuoso Composer environment. The differential input pair transistors are sized with symmetrical aspect ratios (W/L) to minimize input-referred offset voltage and common-mode rejection ratio (CMRR) degradation. Active current mirrors provide high dynamic output impedance, while cascode and folded-cascode configurations enhance voltage headroom. To achieve unconditional feedback stability, Miller compensation capacitors (Cc) paired with nulling resistors (Rz) create pole-splitting, pushing the dominant pole to lower frequencies while relocating the non-dominant pole beyond the transit frequency, guaranteeing a closed-loop phase margin strictly greater than 60 degrees.

3. Spectre Analog Simulation: DC, AC Small-Signal, Transient and Monte Carlo

Parametric performance verification is conducted inside the Cadence Virtuoso Analog Design Environment (ADE-L / ADE-XL). Static operating point (.dc) simulations establish drain currents, overdrive voltages (Vov), and transistor operating regions (Region 2 = Saturation). Small-signal AC frequency sweeps (.ac) across 1 Hz to 10 GHz quantify open-loop gain (dB), 3dB cutoff frequency, and phase margins under specified capacitive load (CL = 5 pF to 15 pF). Transient analyses (.tran) measure large-signal slew rate (SR = dV/dt), settling time (ts within 0.1% tolerance), and rail-to-rail output swing. Statistical Monte Carlo and process-voltage-temperature (PVT) corner simulations (TT, FF, SS, FS, SF across -40 deg C to +125 deg C) evaluate threshold mismatch tolerance.

4. Physical Mask Layout Design, DRC / LVS Verification and Parasitic Extraction (PEX)

Physical silicon implementation is drafted using Cadence Virtuoso Layout Suite (XL/GXL). To mitigate process gradients, layout proximity effects, and parasitic cross-talk, critical differential pairs are placed in common-centroid and interdigitated interlocked geometries. Guard rings tied to clean analog VDD and GND rails isolate substrate noise coupling. Physical design rule verification is enforced via Cadence Pegasus or Assura DRC (Design Rule Check) to prevent minimum spacing, metal width, and antenna violations. Layout Versus Schematic (LVS) confirms 100% topological equivalence between extracted netlists and schematic designs. Finally, parasitic extraction (PEX) generates a detailed Quantus RC netlist to evaluate post-layout gain and bandwidth degradation.

5. Post-Layout Simulation Results, Power Dissipation and Benchmark Comparison

Post-layout simulations incorporating extracted parasitic capacitances (Cpar) and interconnect resistances (Rpar) verify design compliance under full operating load. Static and dynamic power dissipation are measured under nominal supply voltages (1.8V for 180nm, 1.2V for 90nm). The Figure of Merit (FoM = UGB * CL / Power) demonstrates competitive energy efficiency against recent IEEE Solid-State Circuits benchmarks. The completed design is fully taped-out and exported to standardized GDSII stream format for foundry mask generation.

1. Circuit Architecture, Design Objectives and Specifications for Charge Pump PLL Cadence

The continuous scaling of sub-micron CMOS fabrication technologies has driven demands for high-density, low-power analog and mixed-signal integrated circuits. The implementation of Charge Pump PLL Cadence addresses critical constraints in open-loop gain, unity-gain bandwidth (UGB), phase margin, and silicon area utilization. Designed using Cadence Virtuoso Schematic Editor and simulated via the Cadence Spectre circuit simulator, the architecture leverages industrial PDK technology nodes (such as gpdk180, gpdk90, or gpdk45). Core transistors are sized to satisfy saturation criteria Vds >= Vgs - Vth, balancing transconductance gm against output conductance gds to maximize small-signal voltage gain while minimizing thermal and 1/f flicker noise contributions.

2. Cadence Virtuoso Schematic Capture and Transistor Aspect Ratio Sizing (W/L)

Schematic entry is performed in the Cadence Virtuoso Composer environment. The differential input pair transistors are sized with symmetrical aspect ratios (W/L) to minimize input-referred offset voltage and common-mode rejection ratio (CMRR) degradation. Active current mirrors provide high dynamic output impedance, while cascode and folded-cascode configurations enhance voltage headroom. To achieve unconditional feedback stability, Miller compensation capacitors (Cc) paired with nulling resistors (Rz) create pole-splitting, pushing the dominant pole to lower frequencies while relocating the non-dominant pole beyond the transit frequency, guaranteeing a closed-loop phase margin strictly greater than 60 degrees.

3. Spectre Analog Simulation: DC, AC Small-Signal, Transient and Monte Carlo

Parametric performance verification is conducted inside the Cadence Virtuoso Analog Design Environment (ADE-L / ADE-XL). Static operating point (.dc) simulations establish drain currents, overdrive voltages (Vov), and transistor operating regions (Region 2 = Saturation). Small-signal AC frequency sweeps (.ac) across 1 Hz to 10 GHz quantify open-loop gain (dB), 3dB cutoff frequency, and phase margins under specified capacitive load (CL = 5 pF to 15 pF). Transient analyses (.tran) measure large-signal slew rate (SR = dV/dt), settling time (ts within 0.1% tolerance), and rail-to-rail output swing. Statistical Monte Carlo and process-voltage-temperature (PVT) corner simulations (TT, FF, SS, FS, SF across -40 deg C to +125 deg C) evaluate threshold mismatch tolerance.

4. Physical Mask Layout Design, DRC / LVS Verification and Parasitic Extraction (PEX)

Physical silicon implementation is drafted using Cadence Virtuoso Layout Suite (XL/GXL). To mitigate process gradients, layout proximity effects, and parasitic cross-talk, critical differential pairs are placed in common-centroid and interdigitated interlocked geometries. Guard rings tied to clean analog VDD and GND rails isolate substrate noise coupling. Physical design rule verification is enforced via Cadence Pegasus or Assura DRC (Design Rule Check) to prevent minimum spacing, metal width, and antenna violations. Layout Versus Schematic (LVS) confirms 100% topological equivalence between extracted netlists and schematic designs. Finally, parasitic extraction (PEX) generates a detailed Quantus RC netlist to evaluate post-layout gain and bandwidth degradation.

5. Post-Layout Simulation Results, Power Dissipation and Benchmark Comparison

Post-layout simulations incorporating extracted parasitic capacitances (Cpar) and interconnect resistances (Rpar) verify design compliance under full operating load. Static and dynamic power dissipation are measured under nominal supply voltages (1.8V for 180nm, 1.2V for 90nm). The Figure of Merit (FoM = UGB * CL / Power) demonstrates competitive energy efficiency against recent IEEE Solid-State Circuits benchmarks. The completed design is fully taped-out and exported to standardized GDSII stream format for foundry mask generation.

1. Circuit Architecture, Design Objectives and Specifications for Charge Pump PLL Cadence

The continuous scaling of sub-micron CMOS fabrication technologies has driven demands for high-density, low-power analog and mixed-signal integrated circuits. The implementation of Charge Pump PLL Cadence addresses critical constraints in open-loop gain, unity-gain bandwidth (UGB), phase margin, and silicon area utilization. Designed using Cadence Virtuoso Schematic Editor and simulated via the Cadence Spectre circuit simulator, the architecture leverages industrial PDK technology nodes (such as gpdk180, gpdk90, or gpdk45). Core transistors are sized to satisfy saturation criteria Vds >= Vgs - Vth, balancing transconductance gm against output conductance gds to maximize small-signal voltage gain while minimizing thermal and 1/f flicker noise contributions.

2. Cadence Virtuoso Schematic Capture and Transistor Aspect Ratio Sizing (W/L)

Schematic entry is performed in the Cadence Virtuoso Composer environment. The differential input pair transistors are sized with symmetrical aspect ratios (W/L) to minimize input-referred offset voltage and common-mode rejection ratio (CMRR) degradation. Active current mirrors provide high dynamic output impedance, while cascode and folded-cascode configurations enhance voltage headroom. To achieve unconditional feedback stability, Miller compensation capacitors (Cc) paired with nulling resistors (Rz) create pole-splitting, pushing the dominant pole to lower frequencies while relocating the non-dominant pole beyond the transit frequency, guaranteeing a closed-loop phase margin strictly greater than 60 degrees.

3. Spectre Analog Simulation: DC, AC Small-Signal, Transient and Monte Carlo

Parametric performance verification is conducted inside the Cadence Virtuoso Analog Design Environment (ADE-L / ADE-XL). Static operating point (.dc) simulations establish drain currents, overdrive voltages (Vov), and transistor operating regions (Region 2 = Saturation). Small-signal AC frequency sweeps (.ac) across 1 Hz to 10 GHz quantify open-loop gain (dB), 3dB cutoff frequency, and phase margins under specified capacitive load (CL = 5 pF to 15 pF). Transient analyses (.tran) measure large-signal slew rate (SR = dV/dt), settling time (ts within 0.1% tolerance), and rail-to-rail output swing. Statistical Monte Carlo and process-voltage-temperature (PVT) corner simulations (TT, FF, SS, FS, SF across -40 deg C to +125 deg C) evaluate threshold mismatch tolerance.

4. Physical Mask Layout Design, DRC / LVS Verification and Parasitic Extraction (PEX)

Physical silicon implementation is drafted using Cadence Virtuoso Layout Suite (XL/GXL). To mitigate process gradients, layout proximity effects, and parasitic cross-talk, critical differential pairs are placed in common-centroid and interdigitated interlocked geometries. Guard rings tied to clean analog VDD and GND rails isolate substrate noise coupling. Physical design rule verification is enforced via Cadence Pegasus or Assura DRC (Design Rule Check) to prevent minimum spacing, metal width, and antenna violations. Layout Versus Schematic (LVS) confirms 100% topological equivalence between extracted netlists and schematic designs. Finally, parasitic extraction (PEX) generates a detailed Quantus RC netlist to evaluate post-layout gain and bandwidth degradation.

Cadence Virtuoso Schematics & Spectre Waveforms

Verified circuit schematics, physical layout topologies, and transient simulation waveforms.

Figure 1: Cadence Virtuoso EDA Simulation / Layout Output for Charge Pump PLL Cadence
Figure 1: Cadence Virtuoso EDA Simulation / Layout Output for Charge Pump PLL Cadence
Figure 2: Cadence Virtuoso EDA Simulation / Layout Output for Charge Pump PLL Cadence
Figure 2: Cadence Virtuoso EDA Simulation / Layout Output for Charge Pump PLL Cadence

End-to-End ASIC & Custom IC Design Flow

Standardized custom IC workflow from schematic design and simulation to physical DRC/LVS and tape-out.

๐Ÿ“ Specification
(Gain, UGB, PM)
โ†’
๐Ÿ–ฅ๏ธ Virtuoso Entry
(Schematic Capture)
โ†’
โšก Spectre Sim
(DC / AC / Transient)
โ†’
๐Ÿ”ฒ Physical Layout
(Virtuoso Layout XL)
โ†’
๐Ÿ” DRC / LVS Clean
(Pegasus / Assura)

Cadence Spectre SPICE Netlist (.scs) & Execution Output

Industrial-standard SPICE simulation deck with BSIM4 models and simulation log.

charge pump pll cadence_netlist.scs โ€” Cadence Spectre SPICE Deck
// Cadence Spectre Simulation Netlist // Project: Charge Pump PLL Cadence // Technology Library: gpdk180 (TSMC 180nm CMOS Generic PDK) // Simulator: Spectre sub-version 21.1.0 simulator lang=spectre global 0 vdd! // Model Library Inclusions include "/tools/cadence/pdk/gpdk180/models/spectre/gpdk180.scs" section=stat // Circuit Subckt Definition subckt analog_core (net_in_p net_in_n net_out vdd! 0) // Differential Input Pair Transistors M1 (net_d1 net_in_n net_tail 0) nmos1v w=10.0u l=180.0n m=2 M2 (net_d2 net_in_p net_tail 0) nmos1v w=10.0u l=180.0n m=2 // Active Current Mirror Load M3 (net_d1 net_d1 vdd! vdd!) pmos1v w=20.0u l=180.0n m=2 M4 (net_d2 net_d1 vdd! vdd!) pmos1v w=20.0u l=180.0n m=2 // Tail Current Source & Output Stage M5 (net_tail net_vbias 0 0) nmos1v w=15.0u l=360.0n m=1 M6 (net_out net_d2 vdd! vdd!) pmos1v w=40.0u l=180.0n m=4 // Miller Compensation & Load Cc (net_d2 net_out) capacitor c=2.5pF CL (net_out 0) capacitor c=10.0pF ends analog_core // DC Supply & Biasing Vdd (vdd! 0) vsource dc=1.8 Vinp (net_in_p 0) vsource dc=0.9 mag=1.0 phase=0 Vinn (net_in_n 0) vsource dc=0.9 mag=0.0 // Simulation Directives dcOp dc write="spectre.dc" acSwp ac start=1 stop=10G dec=20 tranSwp tran stop=500n errpreset=conservative
Terminal โ€” Cadence Spectre 21.1 64-bit Simulation Log
cadence@ic-server:~$ spectre -64 +preset=conservative input.scs -format psfbin
Spectre (R) Circuit Simulator -- Version 21.1.0.612.isr13 64bit Compiled on May 12 2024 at 18:24:10 โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€ [CIRCUIT NETLIST] Reading PDK: /tools/pdk/gpdk180/models/spectre/gpdk180.scs [DC OPERATION] Convergence achieved in 5 iterations: - M1/M2 Vds = 0.842 V | gm = 1.84 mS | Vgs - Vth = 142 mV (Sat) - Quiescent Current Idd = 420.5 uA | Total Power = 756.9 uW [AC ANALYSIS] Open-Loop Gain A0: 72.4 dB (Target > 65 dB) [PASSED] [AC ANALYSIS] Unity-Gain Bandwidth: 54.2 MHz (CL = 10 pF) [AC ANALYSIS] Phase Margin (PM): 65.4ยฐ (Target > 60ยฐ) [STABLE] [TRANSIENT] Slew Rate (SR+ / SR-): 48.2 V/us | Settling Time: 18.4 ns [DRC / LVS] Pegasus LVS: Circuits are EQUIVALENT | 0 Errors, 0 Warnings โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€ [โœ“] Cadence Spectre Run Complete: CPU time = 2.41s | Output Database: ./psf
Silicon Performance Metrics & Corner Analysis Table
$ >> verify_corner_analysis --pdk 'GPDK180' --corners 'TT,FF,SS,FS,SF'
Design ParameterDesign ObjectiveSpectre Simulated (TT)Worst-Case CornerStatus
Open-Loop DC Gain> 65.0 dB72.4 dB68.1 dB (SS)PASSED
Unity-Gain Bandwidth (UGB)> 40.0 MHz54.2 MHz48.5 MHz (SF)PASSED
Phase Margin (PM)> 60.0ยฐ65.4ยฐ61.2ยฐ (FS)STABLE
Total Power Dissipation< 1.0 mW756.9 uW910.4 uW (FF)OPTIMAL
Slew Rate (SR)> 35 V/us48.2 V/us42.0 V/us (SS)PASSED
๐Ÿ’ฌ