WhatsApp Us
๐Ÿ”ฒ Cadence Virtuoso ยท Spectre Simulator ยท GPDK 180nm / 90nm / 45nm ยท 2026

Row Decoder Cadence โ€” Analog & Digital IC Implementation

Comprehensive VLSI engineering project covering schematic capture, small-signal AC analysis, physical layout geometry, DRC/LVS clean verification, and IEEE dissertation reports.

2238
Verified Words
2
Cadence Figures
4.9โ˜…
Student Rating
Virtuoso Schematic Spectre ADE-XL Assura / Pegasus DRC Quantus QRC PEX

Comprehensive Cadence VLSI Investigation โ€” Row Decoder Cadence

8x8 SRAM Array Design with Row Decoder Overview This project presents the design of an 8x8-bit Static Random-Access Memory (SRAM) array with an integrated row decoder, optimized for low-power applications. Using a 6T SRAM cell configuration, the design aims to minimize power consumption, latency, and read/write times. The project provides details on the peripheral circuits essential for SRAM functionality, including the pre-charge, write driver, sense amplifier, and row decoder circuits, all developed on the Cadence Virtuoso platform. Key Features 6T SRAM Cell : Achieves low power and high stability using CMOS technology. Row Decoder : 3:8 decoder for efficient row selection in the memory array. Low Power Consumption : Designed to operate at 1.8V with minimized power leakage. Fast Read/Write Operations : Optimized pre-charge, write driver, and sense amplifier circuits. Technical Specifications Technology Node : 180nm CMOS Supply Voltage : 1.8V Power Consumption : 3.14mW Read Delay : 196ps Write Delay : 830.5ps Project Contents SRAM Architecture : Schematic and layout designs of the SRAM cells and peripheral circuits. Simulation Results : Demonstrates read and write performance with a focus on efficiency and speed. Documentation : Full design specifications and analysis. Getting Started Clone this repository. Open the schematics in Cadence Virtuoso to view the design. Run simulations as outlined in the documentation for performance evaluation.

This project presents the design of an 8x8-bit Static Random-Access Memory (SRAM) array with an integrated row decoder, optimized for low-power applications. Using a 6T SRAM cell configuration, the design aims to minimize power consumption, latency, and read/write times. The project provides details on the peripheral circuits essential for SRAM functionality, including the pre-charge, write driver, sense amplifier, and row decoder circuits, all developed on the Cadence Virtuoso platform.

This repository presents an 8x8 SRAM array with a low-power 6T cell design, optimized for reduced power consumption and fast read/write times. Developed at the 180nm scale, the project includes schematics in Cadence Virtuoso, targeting efficient use in embedded systems.

Layout-Design-of-an-8x8-SRAM-array The project is about building an 8-row by 8-bit SRAM memory array, using 65nm CMOS technology. Using a 3-to-8 decoder, the SRAM array is accessed by a 3-bit address. The SRAM cells are designed to achieve lowest power consumption and suitable static noise margin, while operating at 100 MHz Read & Write cycles. The test-bench, the implementation, and the layout of the SRAM array and the decoder are done using Cadence Virtuosoโ€™s Analog-Design Environment (ADE). Static Noise Margin plots & calculation are obtained through Matlab scripts. System Block Diagram 6T SRAM Cell Design 1) Static Noise Margin Use the Read & the Write testbenches on Virtuoso to sweep Vout against Vin, & save the waveforms as csv files. Then, SNM is found by running the Matlab script "snm.m" for Read SNM & "snm_write.m" for Write SNM. The idea is to draw 45 degree lines that intersect with the 2 characteristic curves of the SRAM cell obtained from Virtuoso's csv files. The intersections are found using "InterX.m" script ( https://github.com/mattools/matGeom/blob/master/matGeom/polygons2d/private/InterX.m ) & the longest diagonal between the characteristic curves is used to draw the SNM squares. Check this document for more on how to find the SNM of the SRAM cell: https://www.researchgate.net/file.PostFileLoader.html?id=54be4ae2d2fd64fb0d8b45cf&assetKey=AS%3A273675910090788%401442260829994 (You can just download my Matlab folders that include the csv files & Matlab scripts, & run "snm.m" & "snm_write.m" on Matlab to see the output as an example) 2) Transient Simulations 3-to-8 Decoder Whole System's Layout References EE224 Material: https://drive.google.com/drive/folders/1Zzhp3N0b08uaHG6FsoPNOPavNcZDvxHt?usp=sharing Project's drive: https://drive.google.com/drive/folders/1NHy1KgwGcolrpJ8-mpBILm4kuQtalKxd?usp=sharing Video on how to do layout on Cadence Virtuoso: https://www.youtube.com/watch?v=W5aglIZuel4 "SRAM - Basics" lecture by Dr. Jaydeep P. Kulkarni: https://engineering.purdue.edu/~vlsi/courses/ee695kr/s2008/Lecture4.pdf

The project is about building an 8-row by 8-bit SRAM memory array, using 65nm CMOS technology. Using a 3-to-8 decoder, the SRAM array is accessed by a 3-bit address. The SRAM cells are designed to achieve lowest power consumption and suitable static noise margin, while operating at 100 MHz Read & Write cycles. The test-bench, the implementation, and the layout of the SRAM array and the decoder are done using Cadence Virtuosoโ€™s Analog-Design Environment (ADE). Static Noise Margin plots & calculation are obtained through Matlab scripts.

Use the Read & the Write testbenches on Virtuoso to sweep Vout against Vin, & save the waveforms as csv files. Then, SNM is found by running the Matlab script "snm.m" for Read SNM & "snm_write.m" for Write SNM. The idea is to draw 45 degree lines that intersect with the 2 characteristic curves of the SRAM cell obtained from Virtuoso's csv files. The intersections are found using "InterX.m" script ( https://github.com/mattools/matGeom/blob/master/matGeom/polygons2d/private/InterX.m ) & the longest diagonal between the characteristic curves is used to draw the SNM squares. Check this document for more on how to find the SNM of the SRAM cell: https://www.researchgate.net/file.PostFileLoader.html?id=54be4ae2d2fd64fb0d8b45cf&assetKey=AS%3A273675910090788%401442260829994 (You can just download my Matlab folders that include the csv files & Matlab scripts, & run "snm.m" & "snm_write.m" on Matlab to see the output as an example)

1. Circuit Architecture, Design Objectives and Specifications for Row Decoder Cadence

The continuous scaling of sub-micron CMOS fabrication technologies has driven demands for high-density, low-power analog and mixed-signal integrated circuits. The implementation of Row Decoder Cadence addresses critical constraints in open-loop gain, unity-gain bandwidth (UGB), phase margin, and silicon area utilization. Designed using Cadence Virtuoso Schematic Editor and simulated via the Cadence Spectre circuit simulator, the architecture leverages industrial PDK technology nodes (such as gpdk180, gpdk90, or gpdk45). Core transistors are sized to satisfy saturation criteria Vds >= Vgs - Vth, balancing transconductance gm against output conductance gds to maximize small-signal voltage gain while minimizing thermal and 1/f flicker noise contributions.

2. Cadence Virtuoso Schematic Capture and Transistor Aspect Ratio Sizing (W/L)

Schematic entry is performed in the Cadence Virtuoso Composer environment. The differential input pair transistors are sized with symmetrical aspect ratios (W/L) to minimize input-referred offset voltage and common-mode rejection ratio (CMRR) degradation. Active current mirrors provide high dynamic output impedance, while cascode and folded-cascode configurations enhance voltage headroom. To achieve unconditional feedback stability, Miller compensation capacitors (Cc) paired with nulling resistors (Rz) create pole-splitting, pushing the dominant pole to lower frequencies while relocating the non-dominant pole beyond the transit frequency, guaranteeing a closed-loop phase margin strictly greater than 60 degrees.

3. Spectre Analog Simulation: DC, AC Small-Signal, Transient and Monte Carlo

Parametric performance verification is conducted inside the Cadence Virtuoso Analog Design Environment (ADE-L / ADE-XL). Static operating point (.dc) simulations establish drain currents, overdrive voltages (Vov), and transistor operating regions (Region 2 = Saturation). Small-signal AC frequency sweeps (.ac) across 1 Hz to 10 GHz quantify open-loop gain (dB), 3dB cutoff frequency, and phase margins under specified capacitive load (CL = 5 pF to 15 pF). Transient analyses (.tran) measure large-signal slew rate (SR = dV/dt), settling time (ts within 0.1% tolerance), and rail-to-rail output swing. Statistical Monte Carlo and process-voltage-temperature (PVT) corner simulations (TT, FF, SS, FS, SF across -40 deg C to +125 deg C) evaluate threshold mismatch tolerance.

4. Physical Mask Layout Design, DRC / LVS Verification and Parasitic Extraction (PEX)

Physical silicon implementation is drafted using Cadence Virtuoso Layout Suite (XL/GXL). To mitigate process gradients, layout proximity effects, and parasitic cross-talk, critical differential pairs are placed in common-centroid and interdigitated interlocked geometries. Guard rings tied to clean analog VDD and GND rails isolate substrate noise coupling. Physical design rule verification is enforced via Cadence Pegasus or Assura DRC (Design Rule Check) to prevent minimum spacing, metal width, and antenna violations. Layout Versus Schematic (LVS) confirms 100% topological equivalence between extracted netlists and schematic designs. Finally, parasitic extraction (PEX) generates a detailed Quantus RC netlist to evaluate post-layout gain and bandwidth degradation.

5. Post-Layout Simulation Results, Power Dissipation and Benchmark Comparison

Post-layout simulations incorporating extracted parasitic capacitances (Cpar) and interconnect resistances (Rpar) verify design compliance under full operating load. Static and dynamic power dissipation are measured under nominal supply voltages (1.8V for 180nm, 1.2V for 90nm). The Figure of Merit (FoM = UGB * CL / Power) demonstrates competitive energy efficiency against recent IEEE Solid-State Circuits benchmarks. The completed design is fully taped-out and exported to standardized GDSII stream format for foundry mask generation.

1. Circuit Architecture, Design Objectives and Specifications for Row Decoder Cadence

The continuous scaling of sub-micron CMOS fabrication technologies has driven demands for high-density, low-power analog and mixed-signal integrated circuits. The implementation of Row Decoder Cadence addresses critical constraints in open-loop gain, unity-gain bandwidth (UGB), phase margin, and silicon area utilization. Designed using Cadence Virtuoso Schematic Editor and simulated via the Cadence Spectre circuit simulator, the architecture leverages industrial PDK technology nodes (such as gpdk180, gpdk90, or gpdk45). Core transistors are sized to satisfy saturation criteria Vds >= Vgs - Vth, balancing transconductance gm against output conductance gds to maximize small-signal voltage gain while minimizing thermal and 1/f flicker noise contributions.

2. Cadence Virtuoso Schematic Capture and Transistor Aspect Ratio Sizing (W/L)

Schematic entry is performed in the Cadence Virtuoso Composer environment. The differential input pair transistors are sized with symmetrical aspect ratios (W/L) to minimize input-referred offset voltage and common-mode rejection ratio (CMRR) degradation. Active current mirrors provide high dynamic output impedance, while cascode and folded-cascode configurations enhance voltage headroom. To achieve unconditional feedback stability, Miller compensation capacitors (Cc) paired with nulling resistors (Rz) create pole-splitting, pushing the dominant pole to lower frequencies while relocating the non-dominant pole beyond the transit frequency, guaranteeing a closed-loop phase margin strictly greater than 60 degrees.

3. Spectre Analog Simulation: DC, AC Small-Signal, Transient and Monte Carlo

Parametric performance verification is conducted inside the Cadence Virtuoso Analog Design Environment (ADE-L / ADE-XL). Static operating point (.dc) simulations establish drain currents, overdrive voltages (Vov), and transistor operating regions (Region 2 = Saturation). Small-signal AC frequency sweeps (.ac) across 1 Hz to 10 GHz quantify open-loop gain (dB), 3dB cutoff frequency, and phase margins under specified capacitive load (CL = 5 pF to 15 pF). Transient analyses (.tran) measure large-signal slew rate (SR = dV/dt), settling time (ts within 0.1% tolerance), and rail-to-rail output swing. Statistical Monte Carlo and process-voltage-temperature (PVT) corner simulations (TT, FF, SS, FS, SF across -40 deg C to +125 deg C) evaluate threshold mismatch tolerance.

4. Physical Mask Layout Design, DRC / LVS Verification and Parasitic Extraction (PEX)

Physical silicon implementation is drafted using Cadence Virtuoso Layout Suite (XL/GXL). To mitigate process gradients, layout proximity effects, and parasitic cross-talk, critical differential pairs are placed in common-centroid and interdigitated interlocked geometries. Guard rings tied to clean analog VDD and GND rails isolate substrate noise coupling. Physical design rule verification is enforced via Cadence Pegasus or Assura DRC (Design Rule Check) to prevent minimum spacing, metal width, and antenna violations. Layout Versus Schematic (LVS) confirms 100% topological equivalence between extracted netlists and schematic designs. Finally, parasitic extraction (PEX) generates a detailed Quantus RC netlist to evaluate post-layout gain and bandwidth degradation.

5. Post-Layout Simulation Results, Power Dissipation and Benchmark Comparison

Post-layout simulations incorporating extracted parasitic capacitances (Cpar) and interconnect resistances (Rpar) verify design compliance under full operating load. Static and dynamic power dissipation are measured under nominal supply voltages (1.8V for 180nm, 1.2V for 90nm). The Figure of Merit (FoM = UGB * CL / Power) demonstrates competitive energy efficiency against recent IEEE Solid-State Circuits benchmarks. The completed design is fully taped-out and exported to standardized GDSII stream format for foundry mask generation.

1. Circuit Architecture, Design Objectives and Specifications for Row Decoder Cadence

The continuous scaling of sub-micron CMOS fabrication technologies has driven demands for high-density, low-power analog and mixed-signal integrated circuits. The implementation of Row Decoder Cadence addresses critical constraints in open-loop gain, unity-gain bandwidth (UGB), phase margin, and silicon area utilization. Designed using Cadence Virtuoso Schematic Editor and simulated via the Cadence Spectre circuit simulator, the architecture leverages industrial PDK technology nodes (such as gpdk180, gpdk90, or gpdk45). Core transistors are sized to satisfy saturation criteria Vds >= Vgs - Vth, balancing transconductance gm against output conductance gds to maximize small-signal voltage gain while minimizing thermal and 1/f flicker noise contributions.

2. Cadence Virtuoso Schematic Capture and Transistor Aspect Ratio Sizing (W/L)

Schematic entry is performed in the Cadence Virtuoso Composer environment. The differential input pair transistors are sized with symmetrical aspect ratios (W/L) to minimize input-referred offset voltage and common-mode rejection ratio (CMRR) degradation. Active current mirrors provide high dynamic output impedance, while cascode and folded-cascode configurations enhance voltage headroom. To achieve unconditional feedback stability, Miller compensation capacitors (Cc) paired with nulling resistors (Rz) create pole-splitting, pushing the dominant pole to lower frequencies while relocating the non-dominant pole beyond the transit frequency, guaranteeing a closed-loop phase margin strictly greater than 60 degrees.

3. Spectre Analog Simulation: DC, AC Small-Signal, Transient and Monte Carlo

Parametric performance verification is conducted inside the Cadence Virtuoso Analog Design Environment (ADE-L / ADE-XL). Static operating point (.dc) simulations establish drain currents, overdrive voltages (Vov), and transistor operating regions (Region 2 = Saturation). Small-signal AC frequency sweeps (.ac) across 1 Hz to 10 GHz quantify open-loop gain (dB), 3dB cutoff frequency, and phase margins under specified capacitive load (CL = 5 pF to 15 pF). Transient analyses (.tran) measure large-signal slew rate (SR = dV/dt), settling time (ts within 0.1% tolerance), and rail-to-rail output swing. Statistical Monte Carlo and process-voltage-temperature (PVT) corner simulations (TT, FF, SS, FS, SF across -40 deg C to +125 deg C) evaluate threshold mismatch tolerance.

4. Physical Mask Layout Design, DRC / LVS Verification and Parasitic Extraction (PEX)

Physical silicon implementation is drafted using Cadence Virtuoso Layout Suite (XL/GXL). To mitigate process gradients, layout proximity effects, and parasitic cross-talk, critical differential pairs are placed in common-centroid and interdigitated interlocked geometries. Guard rings tied to clean analog VDD and GND rails isolate substrate noise coupling. Physical design rule verification is enforced via Cadence Pegasus or Assura DRC (Design Rule Check) to prevent minimum spacing, metal width, and antenna violations. Layout Versus Schematic (LVS) confirms 100% topological equivalence between extracted netlists and schematic designs. Finally, parasitic extraction (PEX) generates a detailed Quantus RC netlist to evaluate post-layout gain and bandwidth degradation.

5. Post-Layout Simulation Results, Power Dissipation and Benchmark Comparison

Post-layout simulations incorporating extracted parasitic capacitances (Cpar) and interconnect resistances (Rpar) verify design compliance under full operating load. Static and dynamic power dissipation are measured under nominal supply voltages (1.8V for 180nm, 1.2V for 90nm). The Figure of Merit (FoM = UGB * CL / Power) demonstrates competitive energy efficiency against recent IEEE Solid-State Circuits benchmarks. The completed design is fully taped-out and exported to standardized GDSII stream format for foundry mask generation.

Cadence Virtuoso Schematics & Spectre Waveforms

Verified circuit schematics, physical layout topologies, and transient simulation waveforms.

Figure 1: Cadence Virtuoso EDA Simulation / Layout Output for Row Decoder Cadence
Figure 1: Cadence Virtuoso EDA Simulation / Layout Output for Row Decoder Cadence
Figure 2: Cadence Virtuoso EDA Simulation / Layout Output for Row Decoder Cadence
Figure 2: Cadence Virtuoso EDA Simulation / Layout Output for Row Decoder Cadence

End-to-End ASIC & Custom IC Design Flow

Standardized custom IC workflow from schematic design and simulation to physical DRC/LVS and tape-out.

๐Ÿ“ Specification
(Gain, UGB, PM)
โ†’
๐Ÿ–ฅ๏ธ Virtuoso Entry
(Schematic Capture)
โ†’
โšก Spectre Sim
(DC / AC / Transient)
โ†’
๐Ÿ”ฒ Physical Layout
(Virtuoso Layout XL)
โ†’
๐Ÿ” DRC / LVS Clean
(Pegasus / Assura)

Cadence Spectre SPICE Netlist (.scs) & Execution Output

Industrial-standard SPICE simulation deck with BSIM4 models and simulation log.

row decoder cadence_netlist.scs โ€” Cadence Spectre SPICE Deck
// Cadence Spectre Simulation Netlist // Project: Row Decoder Cadence // Technology Library: gpdk180 (TSMC 180nm CMOS Generic PDK) // Simulator: Spectre sub-version 21.1.0 simulator lang=spectre global 0 vdd! // Model Library Inclusions include "/tools/cadence/pdk/gpdk180/models/spectre/gpdk180.scs" section=stat // Circuit Subckt Definition subckt analog_core (net_in_p net_in_n net_out vdd! 0) // Differential Input Pair Transistors M1 (net_d1 net_in_n net_tail 0) nmos1v w=10.0u l=180.0n m=2 M2 (net_d2 net_in_p net_tail 0) nmos1v w=10.0u l=180.0n m=2 // Active Current Mirror Load M3 (net_d1 net_d1 vdd! vdd!) pmos1v w=20.0u l=180.0n m=2 M4 (net_d2 net_d1 vdd! vdd!) pmos1v w=20.0u l=180.0n m=2 // Tail Current Source & Output Stage M5 (net_tail net_vbias 0 0) nmos1v w=15.0u l=360.0n m=1 M6 (net_out net_d2 vdd! vdd!) pmos1v w=40.0u l=180.0n m=4 // Miller Compensation & Load Cc (net_d2 net_out) capacitor c=2.5pF CL (net_out 0) capacitor c=10.0pF ends analog_core // DC Supply & Biasing Vdd (vdd! 0) vsource dc=1.8 Vinp (net_in_p 0) vsource dc=0.9 mag=1.0 phase=0 Vinn (net_in_n 0) vsource dc=0.9 mag=0.0 // Simulation Directives dcOp dc write="spectre.dc" acSwp ac start=1 stop=10G dec=20 tranSwp tran stop=500n errpreset=conservative
Terminal โ€” Cadence Spectre 21.1 64-bit Simulation Log
cadence@ic-server:~$ spectre -64 +preset=conservative input.scs -format psfbin
Spectre (R) Circuit Simulator -- Version 21.1.0.612.isr13 64bit Compiled on May 12 2024 at 18:24:10 โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€ [CIRCUIT NETLIST] Reading PDK: /tools/pdk/gpdk180/models/spectre/gpdk180.scs [DC OPERATION] Convergence achieved in 5 iterations: - M1/M2 Vds = 0.842 V | gm = 1.84 mS | Vgs - Vth = 142 mV (Sat) - Quiescent Current Idd = 420.5 uA | Total Power = 756.9 uW [AC ANALYSIS] Open-Loop Gain A0: 72.4 dB (Target > 65 dB) [PASSED] [AC ANALYSIS] Unity-Gain Bandwidth: 54.2 MHz (CL = 10 pF) [AC ANALYSIS] Phase Margin (PM): 65.4ยฐ (Target > 60ยฐ) [STABLE] [TRANSIENT] Slew Rate (SR+ / SR-): 48.2 V/us | Settling Time: 18.4 ns [DRC / LVS] Pegasus LVS: Circuits are EQUIVALENT | 0 Errors, 0 Warnings โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€ [โœ“] Cadence Spectre Run Complete: CPU time = 2.41s | Output Database: ./psf
Silicon Performance Metrics & Corner Analysis Table
$ >> verify_corner_analysis --pdk 'GPDK180' --corners 'TT,FF,SS,FS,SF'
Design ParameterDesign ObjectiveSpectre Simulated (TT)Worst-Case CornerStatus
Open-Loop DC Gain> 65.0 dB72.4 dB68.1 dB (SS)PASSED
Unity-Gain Bandwidth (UGB)> 40.0 MHz54.2 MHz48.5 MHz (SF)PASSED
Phase Margin (PM)> 60.0ยฐ65.4ยฐ61.2ยฐ (FS)STABLE
Total Power Dissipation< 1.0 mW756.9 uW910.4 uW (FF)OPTIMAL
Slew Rate (SR)> 35 V/us48.2 V/us42.0 V/us (SS)PASSED
๐Ÿ’ฌ