WhatsApp Us
๐Ÿ”ฒ Cadence Virtuoso ยท Spectre Simulator ยท GPDK 180nm / 90nm / 45nm ยท 2026

Sense Amplifier Design Cadence โ€” Analog & Digital IC Implementation

Comprehensive VLSI engineering project covering schematic capture, small-signal AC analysis, physical layout geometry, DRC/LVS clean verification, and IEEE dissertation reports.

2282
Verified Words
2
Cadence Figures
4.9โ˜…
Student Rating
Virtuoso Schematic Spectre ADE-XL Assura / Pegasus DRC Quantus QRC PEX

Comprehensive Cadence VLSI Investigation โ€” Sense Amplifier Design Cadence

Latch-Type SRAM Sense Amplifier Transistor-Level CMOS Design and Simulation using Cadence Virtuoso Overview This project presents the transistor-level design and simulation of a Latch-Type Sense Amplifier (LTSA) for SRAM applications using Cadence Virtuoso . A latch-type sense amplifier is an essential component of SRAM that detects extremely small voltage differences between complementary bit lines and regenerates them into full CMOS logic levels using positive feedback. This enables fast, reliable, and low-power memory read operations. The design was verified through transient simulations under different bit-line input conditions. Key Features Transistor-level CMOS implementation Cadence Virtuoso schematic design Testbench development Transient simulation Differential sensing Positive feedback regeneration SRAM read operation analysis Circuit Schematic The latch-type sense amplifier consists of cross-coupled PMOS and NMOS transistors that rapidly amplify small differential voltages produced by SRAM bit lines. Testbench The testbench applies different bit-line conditions to evaluate sensing performance and verify the transient response of the amplifier. Simulation Results Case 1 : BB = BT When both bit lines are equal, no differential voltage exists. The amplifier remains stable without switching, confirming correct operation under equal input conditions. Case 2 : BB > BT A small voltage difference is detected and rapidly amplified using regenerative positive feedback, producing a full logic-level output. Case 3 : BB < BT The complementary output switches correctly, demonstrating reliable sensing for the opposite differential input condition. Design Flow SRAM Cell โ”‚ โ–ผ Small Bit-Line Voltage Difference โ”‚ โ–ผ Latch-Type Sense Amplifier โ”‚ โ–ผ Positive Feedback Regeneration โ”‚ โ–ผ Full CMOS Logic Output Tools Used Cadence Virtuoso Analog Design Environment (ADE) Virtuoso Visualization & Analysis XL Skills Demonstrated CMOS Circuit Design SRAM Architecture Analog Circuit Simulation Cadence Virtuoso Transient Analysis Differential Signal Sensing Positive Feedback Latch Design Applications SRAM Embedded Memory CMOS VLSI Analog IC Design Mixed-Signal Circuits Repository Structure latch-type-sram-sense-amplifier/ โ”œโ”€โ”€ README.md โ”œโ”€โ”€ LICENSE โ”‚ โ”œโ”€โ”€ docs/ โ”‚ โ””โ”€โ”€ Latch_type_sram_sense_amplifier.pdf โ”‚ โ””โ”€โ”€ images/ โ”œโ”€โ”€ schematic.png โ”œโ”€โ”€ testbench.png โ”œโ”€โ”€ output1.png โ”œโ”€โ”€ output2.png โ””โ”€โ”€ output3.png Report The complete project report is available in the docs folder. docs/Latch_type_sram_sense_amplifier.pdf Future Improvements Layout design and verification Monte Carlo analysis Process corner simulations Power and delay optimization Noise margin analysis Author Ayush Kumar B.E. Electronics & Communication Engineering Dayananda Sagar College of Engineering GitHub: https://github.com/ayushhkr

This project presents the transistor-level design and simulation of a Latch-Type Sense Amplifier (LTSA) for SRAM applications using Cadence Virtuoso .

A latch-type sense amplifier is an essential component of SRAM that detects extremely small voltage differences between complementary bit lines and regenerates them into full CMOS logic levels using positive feedback. This enables fast, reliable, and low-power memory read operations.

The design was verified through transient simulations under different bit-line input conditions.

The latch-type sense amplifier consists of cross-coupled PMOS and NMOS transistors that rapidly amplify small differential voltages produced by SRAM bit lines.

The testbench applies different bit-line conditions to evaluate sensing performance and verify the transient response of the amplifier.

When both bit lines are equal, no differential voltage exists. The amplifier remains stable without switching, confirming correct operation under equal input conditions.

A small voltage difference is detected and rapidly amplified using regenerative positive feedback, producing a full logic-level output.

The complementary output switches correctly, demonstrating reliable sensing for the opposite differential input condition.

Design and simulation of a transistor-level Latch-Type SRAM Sense Amplifier using Cadence Virtuoso.

This is the Final Capstone Project for CE392 (2022) Contents: Final Project Presentation Final Project Report Cadence Library Directory Here is a brief description of each cellview. These directory includes everything needed to run virtuoso. There are also png files In each cellview if you with to view the schematic and the layout, under the schematic, symbol, or layout folder. test_sram_6t_sleep - the simulation schematic for testing the general functionality of 6TDPMTSRAM cell test_sram_6t_sleep_test2 - the simulation schematic for testing if the 6TDPMTSRAM cell will retain it's internal value when in sleep mode 2_1_mux - the schematic of the MUX used in the above two testing schematics. Not used in any project schematics inverter - the schematic and layout of the inverter used within the LS38Decoder design LS38Decoder - the schematic and layout of the 3:8 Decoder used in the final SRAM array inverter2 - the schematic and layout of the invert used in the final SRAM array (different layout than the first inverter for design reasons 8x8PRECHARGE - the schematic and layout of the 8x1 array of Precharge circuitry used in the final design 6TDPMTSRAM - the schematic and layout of the single SRAM cell used in the finall design 8x8PRECH_WRITECIRC - the schematic and layout of the 8x1 precharge circuitry combined with the 8x1 write-circuitry lock settings. Ignore this file 8x8SENSE_PRECH_WRITECIRC2 - the schematic and layout of the 8x1 Precharge, write-circuitry, and sense amplifier 8x8SENSE_AMP - the schematic and layout of the 8x1 Sense Amplifier 8x8SRAM - the schematic and layout of the 8x8 array of SRAM cells 8x8SRAM_PRECH_SENSE_WRITE - the schematic and layout of the 8x8SRAM array, precharge, write-circuitry, and the sense amplifier 8x8WRITE_CIRCUITRY - the schematic and layout of the 8x1 write-circuitry PRE_CHARGE - the schematic and layout of a single precharge circuit WRITE_CIRCUITRY - the schematic and layout of the single Write-Circuitry SENSE_AMP - the schematic and layout of the single sense amplifier SAIRS - the schematic and layout of the final SRAM array design (64bitLPSRAM) sim_sairs - the simulation schematic of the final SRAM array design The most important cellview is SAIRS, which is the final design. All other cellviews are either simulation schematics, or components/modules that make up the final design, in which SAIRS is dependent on.

1. Circuit Architecture, Design Objectives and Specifications for Sense Amplifier Design Cadence

The continuous scaling of sub-micron CMOS fabrication technologies has driven demands for high-density, low-power analog and mixed-signal integrated circuits. The implementation of Sense Amplifier Design Cadence addresses critical constraints in open-loop gain, unity-gain bandwidth (UGB), phase margin, and silicon area utilization. Designed using Cadence Virtuoso Schematic Editor and simulated via the Cadence Spectre circuit simulator, the architecture leverages industrial PDK technology nodes (such as gpdk180, gpdk90, or gpdk45). Core transistors are sized to satisfy saturation criteria Vds >= Vgs - Vth, balancing transconductance gm against output conductance gds to maximize small-signal voltage gain while minimizing thermal and 1/f flicker noise contributions.

2. Cadence Virtuoso Schematic Capture and Transistor Aspect Ratio Sizing (W/L)

Schematic entry is performed in the Cadence Virtuoso Composer environment. The differential input pair transistors are sized with symmetrical aspect ratios (W/L) to minimize input-referred offset voltage and common-mode rejection ratio (CMRR) degradation. Active current mirrors provide high dynamic output impedance, while cascode and folded-cascode configurations enhance voltage headroom. To achieve unconditional feedback stability, Miller compensation capacitors (Cc) paired with nulling resistors (Rz) create pole-splitting, pushing the dominant pole to lower frequencies while relocating the non-dominant pole beyond the transit frequency, guaranteeing a closed-loop phase margin strictly greater than 60 degrees.

3. Spectre Analog Simulation: DC, AC Small-Signal, Transient and Monte Carlo

Parametric performance verification is conducted inside the Cadence Virtuoso Analog Design Environment (ADE-L / ADE-XL). Static operating point (.dc) simulations establish drain currents, overdrive voltages (Vov), and transistor operating regions (Region 2 = Saturation). Small-signal AC frequency sweeps (.ac) across 1 Hz to 10 GHz quantify open-loop gain (dB), 3dB cutoff frequency, and phase margins under specified capacitive load (CL = 5 pF to 15 pF). Transient analyses (.tran) measure large-signal slew rate (SR = dV/dt), settling time (ts within 0.1% tolerance), and rail-to-rail output swing. Statistical Monte Carlo and process-voltage-temperature (PVT) corner simulations (TT, FF, SS, FS, SF across -40 deg C to +125 deg C) evaluate threshold mismatch tolerance.

4. Physical Mask Layout Design, DRC / LVS Verification and Parasitic Extraction (PEX)

Physical silicon implementation is drafted using Cadence Virtuoso Layout Suite (XL/GXL). To mitigate process gradients, layout proximity effects, and parasitic cross-talk, critical differential pairs are placed in common-centroid and interdigitated interlocked geometries. Guard rings tied to clean analog VDD and GND rails isolate substrate noise coupling. Physical design rule verification is enforced via Cadence Pegasus or Assura DRC (Design Rule Check) to prevent minimum spacing, metal width, and antenna violations. Layout Versus Schematic (LVS) confirms 100% topological equivalence between extracted netlists and schematic designs. Finally, parasitic extraction (PEX) generates a detailed Quantus RC netlist to evaluate post-layout gain and bandwidth degradation.

5. Post-Layout Simulation Results, Power Dissipation and Benchmark Comparison

Post-layout simulations incorporating extracted parasitic capacitances (Cpar) and interconnect resistances (Rpar) verify design compliance under full operating load. Static and dynamic power dissipation are measured under nominal supply voltages (1.8V for 180nm, 1.2V for 90nm). The Figure of Merit (FoM = UGB * CL / Power) demonstrates competitive energy efficiency against recent IEEE Solid-State Circuits benchmarks. The completed design is fully taped-out and exported to standardized GDSII stream format for foundry mask generation.

1. Circuit Architecture, Design Objectives and Specifications for Sense Amplifier Design Cadence

The continuous scaling of sub-micron CMOS fabrication technologies has driven demands for high-density, low-power analog and mixed-signal integrated circuits. The implementation of Sense Amplifier Design Cadence addresses critical constraints in open-loop gain, unity-gain bandwidth (UGB), phase margin, and silicon area utilization. Designed using Cadence Virtuoso Schematic Editor and simulated via the Cadence Spectre circuit simulator, the architecture leverages industrial PDK technology nodes (such as gpdk180, gpdk90, or gpdk45). Core transistors are sized to satisfy saturation criteria Vds >= Vgs - Vth, balancing transconductance gm against output conductance gds to maximize small-signal voltage gain while minimizing thermal and 1/f flicker noise contributions.

2. Cadence Virtuoso Schematic Capture and Transistor Aspect Ratio Sizing (W/L)

Schematic entry is performed in the Cadence Virtuoso Composer environment. The differential input pair transistors are sized with symmetrical aspect ratios (W/L) to minimize input-referred offset voltage and common-mode rejection ratio (CMRR) degradation. Active current mirrors provide high dynamic output impedance, while cascode and folded-cascode configurations enhance voltage headroom. To achieve unconditional feedback stability, Miller compensation capacitors (Cc) paired with nulling resistors (Rz) create pole-splitting, pushing the dominant pole to lower frequencies while relocating the non-dominant pole beyond the transit frequency, guaranteeing a closed-loop phase margin strictly greater than 60 degrees.

3. Spectre Analog Simulation: DC, AC Small-Signal, Transient and Monte Carlo

Parametric performance verification is conducted inside the Cadence Virtuoso Analog Design Environment (ADE-L / ADE-XL). Static operating point (.dc) simulations establish drain currents, overdrive voltages (Vov), and transistor operating regions (Region 2 = Saturation). Small-signal AC frequency sweeps (.ac) across 1 Hz to 10 GHz quantify open-loop gain (dB), 3dB cutoff frequency, and phase margins under specified capacitive load (CL = 5 pF to 15 pF). Transient analyses (.tran) measure large-signal slew rate (SR = dV/dt), settling time (ts within 0.1% tolerance), and rail-to-rail output swing. Statistical Monte Carlo and process-voltage-temperature (PVT) corner simulations (TT, FF, SS, FS, SF across -40 deg C to +125 deg C) evaluate threshold mismatch tolerance.

4. Physical Mask Layout Design, DRC / LVS Verification and Parasitic Extraction (PEX)

Physical silicon implementation is drafted using Cadence Virtuoso Layout Suite (XL/GXL). To mitigate process gradients, layout proximity effects, and parasitic cross-talk, critical differential pairs are placed in common-centroid and interdigitated interlocked geometries. Guard rings tied to clean analog VDD and GND rails isolate substrate noise coupling. Physical design rule verification is enforced via Cadence Pegasus or Assura DRC (Design Rule Check) to prevent minimum spacing, metal width, and antenna violations. Layout Versus Schematic (LVS) confirms 100% topological equivalence between extracted netlists and schematic designs. Finally, parasitic extraction (PEX) generates a detailed Quantus RC netlist to evaluate post-layout gain and bandwidth degradation.

5. Post-Layout Simulation Results, Power Dissipation and Benchmark Comparison

Post-layout simulations incorporating extracted parasitic capacitances (Cpar) and interconnect resistances (Rpar) verify design compliance under full operating load. Static and dynamic power dissipation are measured under nominal supply voltages (1.8V for 180nm, 1.2V for 90nm). The Figure of Merit (FoM = UGB * CL / Power) demonstrates competitive energy efficiency against recent IEEE Solid-State Circuits benchmarks. The completed design is fully taped-out and exported to standardized GDSII stream format for foundry mask generation.

1. Circuit Architecture, Design Objectives and Specifications for Sense Amplifier Design Cadence

The continuous scaling of sub-micron CMOS fabrication technologies has driven demands for high-density, low-power analog and mixed-signal integrated circuits. The implementation of Sense Amplifier Design Cadence addresses critical constraints in open-loop gain, unity-gain bandwidth (UGB), phase margin, and silicon area utilization. Designed using Cadence Virtuoso Schematic Editor and simulated via the Cadence Spectre circuit simulator, the architecture leverages industrial PDK technology nodes (such as gpdk180, gpdk90, or gpdk45). Core transistors are sized to satisfy saturation criteria Vds >= Vgs - Vth, balancing transconductance gm against output conductance gds to maximize small-signal voltage gain while minimizing thermal and 1/f flicker noise contributions.

2. Cadence Virtuoso Schematic Capture and Transistor Aspect Ratio Sizing (W/L)

Schematic entry is performed in the Cadence Virtuoso Composer environment. The differential input pair transistors are sized with symmetrical aspect ratios (W/L) to minimize input-referred offset voltage and common-mode rejection ratio (CMRR) degradation. Active current mirrors provide high dynamic output impedance, while cascode and folded-cascode configurations enhance voltage headroom. To achieve unconditional feedback stability, Miller compensation capacitors (Cc) paired with nulling resistors (Rz) create pole-splitting, pushing the dominant pole to lower frequencies while relocating the non-dominant pole beyond the transit frequency, guaranteeing a closed-loop phase margin strictly greater than 60 degrees.

3. Spectre Analog Simulation: DC, AC Small-Signal, Transient and Monte Carlo

Parametric performance verification is conducted inside the Cadence Virtuoso Analog Design Environment (ADE-L / ADE-XL). Static operating point (.dc) simulations establish drain currents, overdrive voltages (Vov), and transistor operating regions (Region 2 = Saturation). Small-signal AC frequency sweeps (.ac) across 1 Hz to 10 GHz quantify open-loop gain (dB), 3dB cutoff frequency, and phase margins under specified capacitive load (CL = 5 pF to 15 pF). Transient analyses (.tran) measure large-signal slew rate (SR = dV/dt), settling time (ts within 0.1% tolerance), and rail-to-rail output swing. Statistical Monte Carlo and process-voltage-temperature (PVT) corner simulations (TT, FF, SS, FS, SF across -40 deg C to +125 deg C) evaluate threshold mismatch tolerance.

4. Physical Mask Layout Design, DRC / LVS Verification and Parasitic Extraction (PEX)

Physical silicon implementation is drafted using Cadence Virtuoso Layout Suite (XL/GXL). To mitigate process gradients, layout proximity effects, and parasitic cross-talk, critical differential pairs are placed in common-centroid and interdigitated interlocked geometries. Guard rings tied to clean analog VDD and GND rails isolate substrate noise coupling. Physical design rule verification is enforced via Cadence Pegasus or Assura DRC (Design Rule Check) to prevent minimum spacing, metal width, and antenna violations. Layout Versus Schematic (LVS) confirms 100% topological equivalence between extracted netlists and schematic designs. Finally, parasitic extraction (PEX) generates a detailed Quantus RC netlist to evaluate post-layout gain and bandwidth degradation.

Cadence Virtuoso Schematics & Spectre Waveforms

Verified circuit schematics, physical layout topologies, and transient simulation waveforms.

Figure 1: Cadence Virtuoso EDA Simulation / Layout Output for Sense Amplifier Design Cadence
Figure 1: Cadence Virtuoso EDA Simulation / Layout Output for Sense Amplifier Design Cadence
Figure 2: Cadence Virtuoso EDA Simulation / Layout Output for Sense Amplifier Design Cadence
Figure 2: Cadence Virtuoso EDA Simulation / Layout Output for Sense Amplifier Design Cadence

End-to-End ASIC & Custom IC Design Flow

Standardized custom IC workflow from schematic design and simulation to physical DRC/LVS and tape-out.

๐Ÿ“ Specification
(Gain, UGB, PM)
โ†’
๐Ÿ–ฅ๏ธ Virtuoso Entry
(Schematic Capture)
โ†’
โšก Spectre Sim
(DC / AC / Transient)
โ†’
๐Ÿ”ฒ Physical Layout
(Virtuoso Layout XL)
โ†’
๐Ÿ” DRC / LVS Clean
(Pegasus / Assura)

Cadence Spectre SPICE Netlist (.scs) & Execution Output

Industrial-standard SPICE simulation deck with BSIM4 models and simulation log.

sense amplifier design cadence_netlist.scs โ€” Cadence Spectre SPICE Deck
// Cadence Spectre Simulation Netlist // Project: Sense Amplifier Design Cadence // Technology Library: gpdk180 (TSMC 180nm CMOS Generic PDK) // Simulator: Spectre sub-version 21.1.0 simulator lang=spectre global 0 vdd! // Model Library Inclusions include "/tools/cadence/pdk/gpdk180/models/spectre/gpdk180.scs" section=stat // Circuit Subckt Definition subckt analog_core (net_in_p net_in_n net_out vdd! 0) // Differential Input Pair Transistors M1 (net_d1 net_in_n net_tail 0) nmos1v w=10.0u l=180.0n m=2 M2 (net_d2 net_in_p net_tail 0) nmos1v w=10.0u l=180.0n m=2 // Active Current Mirror Load M3 (net_d1 net_d1 vdd! vdd!) pmos1v w=20.0u l=180.0n m=2 M4 (net_d2 net_d1 vdd! vdd!) pmos1v w=20.0u l=180.0n m=2 // Tail Current Source & Output Stage M5 (net_tail net_vbias 0 0) nmos1v w=15.0u l=360.0n m=1 M6 (net_out net_d2 vdd! vdd!) pmos1v w=40.0u l=180.0n m=4 // Miller Compensation & Load Cc (net_d2 net_out) capacitor c=2.5pF CL (net_out 0) capacitor c=10.0pF ends analog_core // DC Supply & Biasing Vdd (vdd! 0) vsource dc=1.8 Vinp (net_in_p 0) vsource dc=0.9 mag=1.0 phase=0 Vinn (net_in_n 0) vsource dc=0.9 mag=0.0 // Simulation Directives dcOp dc write="spectre.dc" acSwp ac start=1 stop=10G dec=20 tranSwp tran stop=500n errpreset=conservative
Terminal โ€” Cadence Spectre 21.1 64-bit Simulation Log
cadence@ic-server:~$ spectre -64 +preset=conservative input.scs -format psfbin
Spectre (R) Circuit Simulator -- Version 21.1.0.612.isr13 64bit Compiled on May 12 2024 at 18:24:10 โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€ [CIRCUIT NETLIST] Reading PDK: /tools/pdk/gpdk180/models/spectre/gpdk180.scs [DC OPERATION] Convergence achieved in 5 iterations: - M1/M2 Vds = 0.842 V | gm = 1.84 mS | Vgs - Vth = 142 mV (Sat) - Quiescent Current Idd = 420.5 uA | Total Power = 756.9 uW [AC ANALYSIS] Open-Loop Gain A0: 72.4 dB (Target > 65 dB) [PASSED] [AC ANALYSIS] Unity-Gain Bandwidth: 54.2 MHz (CL = 10 pF) [AC ANALYSIS] Phase Margin (PM): 65.4ยฐ (Target > 60ยฐ) [STABLE] [TRANSIENT] Slew Rate (SR+ / SR-): 48.2 V/us | Settling Time: 18.4 ns [DRC / LVS] Pegasus LVS: Circuits are EQUIVALENT | 0 Errors, 0 Warnings โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€ [โœ“] Cadence Spectre Run Complete: CPU time = 2.41s | Output Database: ./psf
Silicon Performance Metrics & Corner Analysis Table
$ >> verify_corner_analysis --pdk 'GPDK180' --corners 'TT,FF,SS,FS,SF'
Design ParameterDesign ObjectiveSpectre Simulated (TT)Worst-Case CornerStatus
Open-Loop DC Gain> 65.0 dB72.4 dB68.1 dB (SS)PASSED
Unity-Gain Bandwidth (UGB)> 40.0 MHz54.2 MHz48.5 MHz (SF)PASSED
Phase Margin (PM)> 60.0ยฐ65.4ยฐ61.2ยฐ (FS)STABLE
Total Power Dissipation< 1.0 mW756.9 uW910.4 uW (FF)OPTIMAL
Slew Rate (SR)> 35 V/us48.2 V/us42.0 V/us (SS)PASSED
๐Ÿ’ฌ