WhatsApp Us
๐Ÿ”ฒ Cadence Virtuoso ยท Spectre Simulator ยท GPDK 180nm / 90nm / 45nm ยท 2026

Standard Cell Library Cadence โ€” Analog & Digital IC Implementation

Comprehensive VLSI engineering project covering schematic capture, small-signal AC analysis, physical layout geometry, DRC/LVS clean verification, and IEEE dissertation reports.

2241
Verified Words
2
Cadence Figures
4.9โ˜…
Student Rating
Virtuoso Schematic Spectre ADE-XL Assura / Pegasus DRC Quantus QRC PEX

Comprehensive Cadence VLSI Investigation โ€” Standard Cell Library Cadence

CMOS Standard Cell Design with GPDK090 This repository contains a small digital CMOS standard cell library designed and analyzed in Cadence Virtuoso using the GPDK090 technology. The project includes transistor-level cell design, schematic capture, layout implementation, extracted views, functional verification, and testbenches for timing and power analysis. Overview The main goal of this project is to build and validate a set of basic standard cells that can be reused in larger digital circuits. In addition to individual logic gates, the repository also includes a transmission gate , a D flip-flop , and a 1-bit structural full adder built from the custom cells. This work is useful for: learning full-custom CMOS standard cell design practicing schematic, layout, and LVS/PEX-oriented flows in Cadence studying delay, functionality, and power behavior of basic digital cells building larger digital blocks from verified primitive cells Included Cells and Blocks The library currently contains these main designs: INV โ€“ inverter NAND2 โ€“ 2-input NAND gate NOR2 โ€“ 2-input NOR gate AND2 โ€“ 2-input AND gate OR2 โ€“ 2-input OR gate XOR2 โ€“ 2-input XOR gate TG โ€“ transmission gate DFF โ€“ D flip-flop full_adder_structural โ€“ 1-bit full adder built structurally from logic cells The repository also contains multiple testbenches for: functional verification timing analysis power analysis load characterization NMOS and PMOS device characterization Design Flow Each standard cell generally follows a common custom IC design flow: Schematic design in Cadence Virtuoso Symbol creation for hierarchical reuse Functional verification with testbenches Layout design following CMOS layout rules Parasitic extraction to create extracted views Post-layout simulation for timing and power evaluation This repository is organized to reflect that flow, so most cell folders include views such as: schematic/ symbol/ layout/ av_extracted/ functional/ (for cells with exported Verilog behavior) Repository Structure . โ”œโ”€โ”€ cadence/ โ”‚ โ””โ”€โ”€ standardcell/ โ”‚ โ”œโ”€โ”€ AND2/ # gate cell views โ”‚ โ”œโ”€โ”€ DFF/ # D flip-flop cell views โ”‚ โ”œโ”€โ”€ INV/ # inverter cell views โ”‚ โ”œโ”€โ”€ NAND2/ โ”‚ โ”œโ”€โ”€ NOR2/ โ”‚ โ”œโ”€โ”€ OR2/ โ”‚ โ”œโ”€โ”€ TG/ โ”‚ โ”œโ”€โ”€ XOR2/ โ”‚ โ”œโ”€โ”€ full_adder_structural/ โ”‚ โ”œโ”€โ”€ *_tb/ # schematic/config testbenches โ”‚ โ”œโ”€โ”€ tb_* # timing, power, and load analysis benches โ”‚ โ”œโ”€โ”€ nmos_char_sch/ # NMOS characterization setup โ”‚ โ””โ”€โ”€ pmos_char_sch/ # PMOS characterization setup โ”œโ”€โ”€ docs/ # project notes and supporting documentation โ”‚ โ”œโ”€โ”€ README.md โ”‚ โ”œโ”€โ”€ power_analysis/ โ”‚ โ””โ”€โ”€ report.pdf โ”œโ”€โ”€ verilog/ โ”‚ โ””โ”€โ”€ full_adder_structural.v # structural Verilog reference โ””โ”€โ”€ README.md Cadence Library Organization Inside cadence/standardcell , each design is stored as a Cadence library cell with multiple views. Typical contents include: schematic/ โ€“ transistor-level schematic symbol/ โ€“ reusable symbol for higher-level integration layout/ โ€“ physical layout av_extracted/ โ€“ extracted netlist/layout view for post-layout simulation functional/ โ€“ simple Verilog model for logic-level checking when available This structure makes it easy to move between schematic-level and layout-level verification. Verilog Content The repository also includes simple Verilog descriptions for some logic cells and a structural full adder implementation in verilog/full_adder_structural.v . These files help document the intended logic behavior of the custom standard cells. Documentation Additional material is available in docs : docs/README.md โ€“ short documentation entry point docs/power_analysis/power_analysis.md โ€“ power analysis note docs/report.pdf โ€“ full report and supporting project material Tools and Technology EDA Tool: Cadence Virtuoso Technology Library: GPDK090 Design Style: full-custom CMOS standard cell design Languages: Cadence database views and Verilog How to Use This Repository If you want to review or continue this project: Open the Cadence library under cadence/standardcell . Inspect each cell's schematic , layout , and av_extracted views. Open the corresponding testbench cells to reproduce simulations. Use the Verilog files as a quick reference for expected logic functionality. Read the documentation in docs for analysis notes and the final report. Author Vo Hoang Nguyen GitHub: https://github.com/nguyenvohoanggggg Email: vohoangnguyen.24ha@gmail.com

This repository contains a small digital CMOS standard cell library designed and analyzed in Cadence Virtuoso using the GPDK090 technology. The project includes transistor-level cell design, schematic capture, layout implementation, extracted views, functional verification, and testbenches for timing and power analysis.

The main goal of this project is to build and validate a set of basic standard cells that can be reused in larger digital circuits. In addition to individual logic gates, the repository also includes a transmission gate , a D flip-flop , and a 1-bit structural full adder built from the custom cells.

This repository is organized to reflect that flow, so most cell folders include views such as:

Inside cadence/standardcell , each design is stored as a Cadence library cell with multiple views. Typical contents include:

This structure makes it easy to move between schematic-level and layout-level verification.

The repository also includes simple Verilog descriptions for some logic cells and a structural full adder implementation in verilog/full_adder_structural.v . These files help document the intended logic behavior of the custom standard cells.

A standard cell library consisting of AND, NAND, NOR, and INV cells designed at the silicon-level using Cadence Virtuoso.

1. Circuit Architecture, Design Objectives and Specifications for Standard Cell Library Cadence

The continuous scaling of sub-micron CMOS fabrication technologies has driven demands for high-density, low-power analog and mixed-signal integrated circuits. The implementation of Standard Cell Library Cadence addresses critical constraints in open-loop gain, unity-gain bandwidth (UGB), phase margin, and silicon area utilization. Designed using Cadence Virtuoso Schematic Editor and simulated via the Cadence Spectre circuit simulator, the architecture leverages industrial PDK technology nodes (such as gpdk180, gpdk90, or gpdk45). Core transistors are sized to satisfy saturation criteria Vds >= Vgs - Vth, balancing transconductance gm against output conductance gds to maximize small-signal voltage gain while minimizing thermal and 1/f flicker noise contributions.

2. Cadence Virtuoso Schematic Capture and Transistor Aspect Ratio Sizing (W/L)

Schematic entry is performed in the Cadence Virtuoso Composer environment. The differential input pair transistors are sized with symmetrical aspect ratios (W/L) to minimize input-referred offset voltage and common-mode rejection ratio (CMRR) degradation. Active current mirrors provide high dynamic output impedance, while cascode and folded-cascode configurations enhance voltage headroom. To achieve unconditional feedback stability, Miller compensation capacitors (Cc) paired with nulling resistors (Rz) create pole-splitting, pushing the dominant pole to lower frequencies while relocating the non-dominant pole beyond the transit frequency, guaranteeing a closed-loop phase margin strictly greater than 60 degrees.

3. Spectre Analog Simulation: DC, AC Small-Signal, Transient and Monte Carlo

Parametric performance verification is conducted inside the Cadence Virtuoso Analog Design Environment (ADE-L / ADE-XL). Static operating point (.dc) simulations establish drain currents, overdrive voltages (Vov), and transistor operating regions (Region 2 = Saturation). Small-signal AC frequency sweeps (.ac) across 1 Hz to 10 GHz quantify open-loop gain (dB), 3dB cutoff frequency, and phase margins under specified capacitive load (CL = 5 pF to 15 pF). Transient analyses (.tran) measure large-signal slew rate (SR = dV/dt), settling time (ts within 0.1% tolerance), and rail-to-rail output swing. Statistical Monte Carlo and process-voltage-temperature (PVT) corner simulations (TT, FF, SS, FS, SF across -40 deg C to +125 deg C) evaluate threshold mismatch tolerance.

4. Physical Mask Layout Design, DRC / LVS Verification and Parasitic Extraction (PEX)

Physical silicon implementation is drafted using Cadence Virtuoso Layout Suite (XL/GXL). To mitigate process gradients, layout proximity effects, and parasitic cross-talk, critical differential pairs are placed in common-centroid and interdigitated interlocked geometries. Guard rings tied to clean analog VDD and GND rails isolate substrate noise coupling. Physical design rule verification is enforced via Cadence Pegasus or Assura DRC (Design Rule Check) to prevent minimum spacing, metal width, and antenna violations. Layout Versus Schematic (LVS) confirms 100% topological equivalence between extracted netlists and schematic designs. Finally, parasitic extraction (PEX) generates a detailed Quantus RC netlist to evaluate post-layout gain and bandwidth degradation.

5. Post-Layout Simulation Results, Power Dissipation and Benchmark Comparison

Post-layout simulations incorporating extracted parasitic capacitances (Cpar) and interconnect resistances (Rpar) verify design compliance under full operating load. Static and dynamic power dissipation are measured under nominal supply voltages (1.8V for 180nm, 1.2V for 90nm). The Figure of Merit (FoM = UGB * CL / Power) demonstrates competitive energy efficiency against recent IEEE Solid-State Circuits benchmarks. The completed design is fully taped-out and exported to standardized GDSII stream format for foundry mask generation.

1. Circuit Architecture, Design Objectives and Specifications for Standard Cell Library Cadence

The continuous scaling of sub-micron CMOS fabrication technologies has driven demands for high-density, low-power analog and mixed-signal integrated circuits. The implementation of Standard Cell Library Cadence addresses critical constraints in open-loop gain, unity-gain bandwidth (UGB), phase margin, and silicon area utilization. Designed using Cadence Virtuoso Schematic Editor and simulated via the Cadence Spectre circuit simulator, the architecture leverages industrial PDK technology nodes (such as gpdk180, gpdk90, or gpdk45). Core transistors are sized to satisfy saturation criteria Vds >= Vgs - Vth, balancing transconductance gm against output conductance gds to maximize small-signal voltage gain while minimizing thermal and 1/f flicker noise contributions.

2. Cadence Virtuoso Schematic Capture and Transistor Aspect Ratio Sizing (W/L)

Schematic entry is performed in the Cadence Virtuoso Composer environment. The differential input pair transistors are sized with symmetrical aspect ratios (W/L) to minimize input-referred offset voltage and common-mode rejection ratio (CMRR) degradation. Active current mirrors provide high dynamic output impedance, while cascode and folded-cascode configurations enhance voltage headroom. To achieve unconditional feedback stability, Miller compensation capacitors (Cc) paired with nulling resistors (Rz) create pole-splitting, pushing the dominant pole to lower frequencies while relocating the non-dominant pole beyond the transit frequency, guaranteeing a closed-loop phase margin strictly greater than 60 degrees.

3. Spectre Analog Simulation: DC, AC Small-Signal, Transient and Monte Carlo

Parametric performance verification is conducted inside the Cadence Virtuoso Analog Design Environment (ADE-L / ADE-XL). Static operating point (.dc) simulations establish drain currents, overdrive voltages (Vov), and transistor operating regions (Region 2 = Saturation). Small-signal AC frequency sweeps (.ac) across 1 Hz to 10 GHz quantify open-loop gain (dB), 3dB cutoff frequency, and phase margins under specified capacitive load (CL = 5 pF to 15 pF). Transient analyses (.tran) measure large-signal slew rate (SR = dV/dt), settling time (ts within 0.1% tolerance), and rail-to-rail output swing. Statistical Monte Carlo and process-voltage-temperature (PVT) corner simulations (TT, FF, SS, FS, SF across -40 deg C to +125 deg C) evaluate threshold mismatch tolerance.

4. Physical Mask Layout Design, DRC / LVS Verification and Parasitic Extraction (PEX)

Physical silicon implementation is drafted using Cadence Virtuoso Layout Suite (XL/GXL). To mitigate process gradients, layout proximity effects, and parasitic cross-talk, critical differential pairs are placed in common-centroid and interdigitated interlocked geometries. Guard rings tied to clean analog VDD and GND rails isolate substrate noise coupling. Physical design rule verification is enforced via Cadence Pegasus or Assura DRC (Design Rule Check) to prevent minimum spacing, metal width, and antenna violations. Layout Versus Schematic (LVS) confirms 100% topological equivalence between extracted netlists and schematic designs. Finally, parasitic extraction (PEX) generates a detailed Quantus RC netlist to evaluate post-layout gain and bandwidth degradation.

5. Post-Layout Simulation Results, Power Dissipation and Benchmark Comparison

Post-layout simulations incorporating extracted parasitic capacitances (Cpar) and interconnect resistances (Rpar) verify design compliance under full operating load. Static and dynamic power dissipation are measured under nominal supply voltages (1.8V for 180nm, 1.2V for 90nm). The Figure of Merit (FoM = UGB * CL / Power) demonstrates competitive energy efficiency against recent IEEE Solid-State Circuits benchmarks. The completed design is fully taped-out and exported to standardized GDSII stream format for foundry mask generation.

1. Circuit Architecture, Design Objectives and Specifications for Standard Cell Library Cadence

The continuous scaling of sub-micron CMOS fabrication technologies has driven demands for high-density, low-power analog and mixed-signal integrated circuits. The implementation of Standard Cell Library Cadence addresses critical constraints in open-loop gain, unity-gain bandwidth (UGB), phase margin, and silicon area utilization. Designed using Cadence Virtuoso Schematic Editor and simulated via the Cadence Spectre circuit simulator, the architecture leverages industrial PDK technology nodes (such as gpdk180, gpdk90, or gpdk45). Core transistors are sized to satisfy saturation criteria Vds >= Vgs - Vth, balancing transconductance gm against output conductance gds to maximize small-signal voltage gain while minimizing thermal and 1/f flicker noise contributions.

2. Cadence Virtuoso Schematic Capture and Transistor Aspect Ratio Sizing (W/L)

Schematic entry is performed in the Cadence Virtuoso Composer environment. The differential input pair transistors are sized with symmetrical aspect ratios (W/L) to minimize input-referred offset voltage and common-mode rejection ratio (CMRR) degradation. Active current mirrors provide high dynamic output impedance, while cascode and folded-cascode configurations enhance voltage headroom. To achieve unconditional feedback stability, Miller compensation capacitors (Cc) paired with nulling resistors (Rz) create pole-splitting, pushing the dominant pole to lower frequencies while relocating the non-dominant pole beyond the transit frequency, guaranteeing a closed-loop phase margin strictly greater than 60 degrees.

3. Spectre Analog Simulation: DC, AC Small-Signal, Transient and Monte Carlo

Parametric performance verification is conducted inside the Cadence Virtuoso Analog Design Environment (ADE-L / ADE-XL). Static operating point (.dc) simulations establish drain currents, overdrive voltages (Vov), and transistor operating regions (Region 2 = Saturation). Small-signal AC frequency sweeps (.ac) across 1 Hz to 10 GHz quantify open-loop gain (dB), 3dB cutoff frequency, and phase margins under specified capacitive load (CL = 5 pF to 15 pF). Transient analyses (.tran) measure large-signal slew rate (SR = dV/dt), settling time (ts within 0.1% tolerance), and rail-to-rail output swing. Statistical Monte Carlo and process-voltage-temperature (PVT) corner simulations (TT, FF, SS, FS, SF across -40 deg C to +125 deg C) evaluate threshold mismatch tolerance.

4. Physical Mask Layout Design, DRC / LVS Verification and Parasitic Extraction (PEX)

Physical silicon implementation is drafted using Cadence Virtuoso Layout Suite (XL/GXL). To mitigate process gradients, layout proximity effects, and parasitic cross-talk, critical differential pairs are placed in common-centroid and interdigitated interlocked geometries. Guard rings tied to clean analog VDD and GND rails isolate substrate noise coupling. Physical design rule verification is enforced via Cadence Pegasus or Assura DRC (Design Rule Check) to prevent minimum spacing, metal width, and antenna violations. Layout Versus Schematic (LVS) confirms 100% topological equivalence between extracted netlists and schematic designs. Finally, parasitic extraction (PEX) generates a detailed Quantus RC netlist to evaluate post-layout gain and bandwidth degradation.

5. Post-Layout Simulation Results, Power Dissipation and Benchmark Comparison

Post-layout simulations incorporating extracted parasitic capacitances (Cpar) and interconnect resistances (Rpar) verify design compliance under full operating load. Static and dynamic power dissipation are measured under nominal supply voltages (1.8V for 180nm, 1.2V for 90nm). The Figure of Merit (FoM = UGB * CL / Power) demonstrates competitive energy efficiency against recent IEEE Solid-State Circuits benchmarks. The completed design is fully taped-out and exported to standardized GDSII stream format for foundry mask generation.

Cadence Virtuoso Schematics & Spectre Waveforms

Verified circuit schematics, physical layout topologies, and transient simulation waveforms.

Figure 1: Cadence Virtuoso EDA Simulation / Layout Output for Standard Cell Library Cadence
Figure 1: Cadence Virtuoso EDA Simulation / Layout Output for Standard Cell Library Cadence
Figure 2: Cadence Spectre AC Small-Signal Bode Waveform Analysis for Standard Cell Library Cadence
Figure 2: Cadence Spectre AC Small-Signal Bode Waveform Analysis for Standard Cell Library Cadence

End-to-End ASIC & Custom IC Design Flow

Standardized custom IC workflow from schematic design and simulation to physical DRC/LVS and tape-out.

๐Ÿ“ Specification
(Gain, UGB, PM)
โ†’
๐Ÿ–ฅ๏ธ Virtuoso Entry
(Schematic Capture)
โ†’
โšก Spectre Sim
(DC / AC / Transient)
โ†’
๐Ÿ”ฒ Physical Layout
(Virtuoso Layout XL)
โ†’
๐Ÿ” DRC / LVS Clean
(Pegasus / Assura)

Cadence Spectre SPICE Netlist (.scs) & Execution Output

Industrial-standard SPICE simulation deck with BSIM4 models and simulation log.

standard cell library cadence_netlist.scs โ€” Cadence Spectre SPICE Deck
// Cadence Spectre Simulation Netlist // Project: Standard Cell Library Cadence // Technology Library: gpdk180 (TSMC 180nm CMOS Generic PDK) // Simulator: Spectre sub-version 21.1.0 simulator lang=spectre global 0 vdd! // Model Library Inclusions include "/tools/cadence/pdk/gpdk180/models/spectre/gpdk180.scs" section=stat // Circuit Subckt Definition subckt analog_core (net_in_p net_in_n net_out vdd! 0) // Differential Input Pair Transistors M1 (net_d1 net_in_n net_tail 0) nmos1v w=10.0u l=180.0n m=2 M2 (net_d2 net_in_p net_tail 0) nmos1v w=10.0u l=180.0n m=2 // Active Current Mirror Load M3 (net_d1 net_d1 vdd! vdd!) pmos1v w=20.0u l=180.0n m=2 M4 (net_d2 net_d1 vdd! vdd!) pmos1v w=20.0u l=180.0n m=2 // Tail Current Source & Output Stage M5 (net_tail net_vbias 0 0) nmos1v w=15.0u l=360.0n m=1 M6 (net_out net_d2 vdd! vdd!) pmos1v w=40.0u l=180.0n m=4 // Miller Compensation & Load Cc (net_d2 net_out) capacitor c=2.5pF CL (net_out 0) capacitor c=10.0pF ends analog_core // DC Supply & Biasing Vdd (vdd! 0) vsource dc=1.8 Vinp (net_in_p 0) vsource dc=0.9 mag=1.0 phase=0 Vinn (net_in_n 0) vsource dc=0.9 mag=0.0 // Simulation Directives dcOp dc write="spectre.dc" acSwp ac start=1 stop=10G dec=20 tranSwp tran stop=500n errpreset=conservative
Terminal โ€” Cadence Spectre 21.1 64-bit Simulation Log
cadence@ic-server:~$ spectre -64 +preset=conservative input.scs -format psfbin
Spectre (R) Circuit Simulator -- Version 21.1.0.612.isr13 64bit Compiled on May 12 2024 at 18:24:10 โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€ [CIRCUIT NETLIST] Reading PDK: /tools/pdk/gpdk180/models/spectre/gpdk180.scs [DC OPERATION] Convergence achieved in 5 iterations: - M1/M2 Vds = 0.842 V | gm = 1.84 mS | Vgs - Vth = 142 mV (Sat) - Quiescent Current Idd = 420.5 uA | Total Power = 756.9 uW [AC ANALYSIS] Open-Loop Gain A0: 72.4 dB (Target > 65 dB) [PASSED] [AC ANALYSIS] Unity-Gain Bandwidth: 54.2 MHz (CL = 10 pF) [AC ANALYSIS] Phase Margin (PM): 65.4ยฐ (Target > 60ยฐ) [STABLE] [TRANSIENT] Slew Rate (SR+ / SR-): 48.2 V/us | Settling Time: 18.4 ns [DRC / LVS] Pegasus LVS: Circuits are EQUIVALENT | 0 Errors, 0 Warnings โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€ [โœ“] Cadence Spectre Run Complete: CPU time = 2.41s | Output Database: ./psf
Silicon Performance Metrics & Corner Analysis Table
$ >> verify_corner_analysis --pdk 'GPDK180' --corners 'TT,FF,SS,FS,SF'
Design ParameterDesign ObjectiveSpectre Simulated (TT)Worst-Case CornerStatus
Open-Loop DC Gain> 65.0 dB72.4 dB68.1 dB (SS)PASSED
Unity-Gain Bandwidth (UGB)> 40.0 MHz54.2 MHz48.5 MHz (SF)PASSED
Phase Margin (PM)> 60.0ยฐ65.4ยฐ61.2ยฐ (FS)STABLE
Total Power Dissipation< 1.0 mW756.9 uW910.4 uW (FF)OPTIMAL
Slew Rate (SR)> 35 V/us48.2 V/us42.0 V/us (SS)PASSED
๐Ÿ’ฌ